Great-plains Disk Harrow Field Update Disk Gang Bearings User Manual download pdf

Great Plains Mfg., Inc. Installation Instructions

11/20/2007 SeriesI 3323DH-4336DH Disk Gang Update 557-329M

Disk Harrow Field Update

Disk Gang Bearings

Applies to Models: Update Kit Numbers:

• 3323 557-301V Bearing & Washers 557-317V Washer Only

• 3326 557-302V Bearing & Washers 557-318V Washer Only

• 3329 557-303V Bearing & Washers 557-319V Washer Only

• 4330 557-304V Bearing & Washers 557-320V Washer Only

• 4333 557-305V Bearing & Washers 557-321V Washer Only

• 4336 557-306V Bearing & Washers & C-Shank 557-322V Washer Only & C-Shank

General Information

These instructions explain how to install

the Bearing and Washer Update Kits. If you are

updating a new machine use the Washer Only

Kit. If you have a used machine you will use

the Bearing Kit. If you have model 4336 disk

harrow you will have to install 1 new c-shank

assembly on 2 gangs. This will be explained in

the Assembly Instructions.

Manual Update

Refer the Disk Harrow operator’s

manual for detailed information on safely

operating, maintaining and it is very important

to grease bearings as shown in operator’s

manual. Refer to parts manual for part

identification.

556-100M Operator’s Manual

556-100P Parts Manual

Before You Start

For safety it is best to park machine on

level concrete floor. Leave machine hooked to

tractor or some kind of hydraulic source so you

can raise machine up and down while you are

assembling Kits. Review these instructions and

make sure you understand where and how the

components are installed, and which existing

parts are removed or re-used.

Tools Required

 Basic Hand Tools



Torque Wrench or 6’ Cheater



Gang Wrenches (provided with

machine)

Assembly Instructions

Refer to drawings on pages 3-5.

Start by unfolding the wings and

removing transport lock from lift cylinders

and lower the machine to the ground. Loosen

the scraper assemblies from the c-shank plate

bottom (13) by loosening the 1/2 x 2 1/32 x 3

u-bolts and sliding the scraper assemblies

over enough to clear gangs but don’t take

them clear off. Removal of hose hangers on

scrapers may be necessary to slide scrapers

over.

Remove the 3/4 hex nuts and 3/4 lock

washers off the 3/4 x 7 hex bolts (1) from

each gang. Raise machine up for clearance

and roll gang out from under machine. You

can take all the wing gangs loose at once and

fold wings back up. Note: Tighten scrapers

before folding wings so bar will not get bent

while folding.

If this is a new machine and you will

be re-installing these bearings, pull the bottom

bearing casting off the bearings. Verify that

1 2 3 4 5 6 7

Summary of Contents

Page 1 - Disk Harrow Field Update

Great Plains Mfg., Inc. Installation Instructions 11/20/2007 SeriesI 3323DH-4336DH Disk Gang Update 557-329M 1 Disk Harrow Field Update Di

Page 2

Installation Instructions Great Plains Mfg., Inc. SeriesI 3323DH-4336DH Disk Gang Update 557-329M 11/20/2007 2 the grease path is correc

Page 3 - Installation Instructions

Great Plains Mfg., Inc. Installation Instructions 11/20/2007 SeriesI 3323D

Page 4 - C-Shank & Bearing

Installation Instructions Great Plains Mfg., Inc. SeriesI 3323DH-4336DH Disk Gang Update 557-329M 11/20/2007 4 00927 On 4336, Install Add

Page 5

Great Plains Mfg., Inc. Installation Instructions 11/20/2007 SeriesI 3323D

Page 6 - Appendix

Installation Instructions Great Plains Mfg., Inc. SeriesI 3323DH-4336DH Disk Gang Update 557-329M 11/20/2007 6 Appendix Disk Gang Bol

Page 7

Great Plains Manufacturing, Inc. Corporate Office: PO. Box 5060 Salina, Kansas 67402-5060 USA

Comments to this Manuals

No comments

Great-plains Disk Harrow Field Update Disk Gang Bearings User Manual

Browse online or download User Manual for Hardware Great-plains Disk Harrow Field Update Disk Gang Bearings. Great Plains Disk Harrow Field Update Disk Gang Bearings User Manual [de]

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Great-plains Disk Harrow Field Update Disk Gang Bearings