Great-plains 1625AHL Operator Manual User Manual Page 26
- Page / 176
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
22 1625AH Table of Contents Index Great Plains Manufacturing, Inc.
411-020M Table of Contents Index 2014-04-21
Store Main Parking Stand
Refer to Figure 8
13. Raise the 3-point hitch slightly.
14. Remove the lower pin holding the parking
stand . Swing the parking stand back and up until it
is above the rear hole . Place the holding pin in the
rear hole and allow the parking stand to rest on it.
This is the transport position for the parking stand.
15. Adjust the top link of a 3-point long enough so the
ball swivel does not bottom out when fully raised.
16. Secure hoses using hose post loops (not shown) so
that hoses have ample slack for lifts and turns, but
cannot get caught in tongue lock or ball swivel.
Failure to do so could cause hose to be crushed
requiring hose replacement.
Monitor Setup
Refer to Figure 9
Model 1625AH planters include one of two
DICKEY-john
®
seed monitors, depending on row count
and fertilizer type:
• IntelliAg
®
MVT (Mini Virtual Terminal)
• PM400
Either systems monitors the following elements of a
1625AH planter:
• seeds at each row unit seed tube;
• ground speed;
• dry fertilizer at row drop tubes (1625AHD models);
and,
• dry fertilizer hopper level (1625AHD models).
MVT Monitor Setup
See “MVT Console Installation” on page 156.
Refer to the DICKEY-john
®
IntelliAg
®
MVT Manual
(11001-1643) for monitor operations, and the MVT Quick
Start Guide (11001-16
a
) for setup.
PM400 Monitor Setup
See “PM400 Console Installation” on page 156.
Refer to the DICKEY-john
®
PM400 Console Manual
(11001-1372) for monitor operations.
After installation, and prior to first field use, the monitor
must be setup with the row spacing and speed sensor
constant, as well as your preferences for information
display. Row count is auto-assigned, but any other
DICKEY-john
®
default values are not likely to be correct
for your planter.
Row spacing data may be found in the Appendix.
Figure 8
Storing Parking Stand
22813
5
6
7
5
7
6
Figure 9
PM400 and MVT Monitors
36211
36218
- Operator 1
- Table of Contents 3
- Important Safety Information 5
- Handle Chemicals Properly 7
- Keep Riders Off Machinery 7
- Use Safety Lights and Devices 7
- Transport Machinery Safely 8
- Shutdown and Storage 8
- Tire Safety 8
- Practice Safe Maintenance 9
- Safety At All Times 9
- Safety Decals 10
- Amber Reflectors 11
- 838-267C 11
- Daytime Reflectors 11
- 838-265C 11
- 818-323C (Option) 12
- Danger: Chemical Hazard 12
- 818-590C 12
- Danger: Crushing Hazard 12
- EXCESSIVE SPEED HAZARD 14
- 818-632C 16
- Warning: Fan Hazard 16
- 818-860C 16
- Warning: Moving Parts 16
- 818-398C 18
- Caution: Tires Not A Step 18
- 838-426C 18
- Caution: Tire Pressure 18
- 858-011C 19
- Introduction 20
- Using This Manual 21
- Document Family 21
- Owner Assistance 21
- Preparation and Setup 22
- Hitching Tractor to Planter 23
- Hydraulic Hose Hookup 24
- Monitor Setup 26
- Marker Setup (Option) 27
- Operating Instructions 28
- Unfolding the Planter 30
- Raising/Lowering Planter 33
- Folding the Planter 34
- Install Lock Channels 35
- Activate Fold Solenoid Valves 35
- Begin Folding 35
- Transporting 37
- Transport Weights 38
- Loading Materials 39
- Monitor Operation 46
- Ground Drive Lock-Up 47
- Seed Meter Drive Lock-Up 49
- Field Setup Checklist 50
- Air System Operation 52
- Meter Operation 54
- Fan Operation 55
- 858-193C 56
- 848-020C 57
- Figure 45 60
- Dry Fertilizer System 62
- Liquid Fertilizer Operation 64
- Dry Fertilizer Operation 64
- Marker Operation 65
- Field Operation 66
- Adjustments 69
- Setting Material Rates 70
- Marker Adjustments 72
- Row Implement Adjustments 73
- 362363196 75
- SHARP OBJECT HAZARD 77
- Depth of (new) coulter blade 78
- Side Gauge Wheel Adjustment 81
- Row Unit Shut-Off 87
- Troubleshooting 92
- Seed Pool Troubleshooting 93
- Population Too Low 95
- Seed Population Too High 97
- Population Related 99
- Problem Cause Solution 100
- No Fertilizer 100
- General Troubleshooting 102
- Maintenance and Lubrication 105
- Height Switch Adjustment 106
- Material Clean-Out 107
- Dry Fertilizer Clean-Out 110
- Liquid Fertilizer Clean-Out 114
- Liquid Fertilizer Maintenance 115
- Seed Meter Maintenance 116
- Bleeding Hydraulics 119
- Marker Maintenance 120
- Chain Maintenance 121
- Per Hopper 124
- Caster Wheel Pivot 128
- As Required 129
- Seasonal 130
- Seed Lubricants 132
- Options and Accessories 133
- Frame-Mounted Row Accessories 134
- Row Options (Unit-Mount) 135
- Rigid Row Cleaners (UMRC) 136
- Seed Meter Disks 137
- Inside Disc Scrapers 137
- Gauge Wheel Scrapers 138
- Lock-Up Pins 138
- Seed Tube Brush 138
- Seed Firmers 139
- Paddle Wheel Kit 140
- Seed Lubricant 140
- Specifications and Capacities 141
- 47 feet 7 inches (14.50 m) 144
- Torque Values Chart 149
- Tire Inflation Chart 149
- Chain Routing 150
- Appendix B - Pre-Delivery 154
- 803-021C NUT HEX 5/8-11 PLT 155
- Marker Assembly 156
- 803-019C NUT LOCK 1/2-13 PLT 157
- Press Wheel Installation 158
- Appendix C - Initial Setup 160
- PM400 Monitor Quick-Start 161
- Level Planter 163
- Wing Alignment 164
- Speed Calibration 165
- Marker Extension 165
- 122-278S Scraper Installation 167
- Table of Contents Index 175
- Salina, Kansas 67402-5060 USA 176
Related products and manuals for Gardening equipment Great-plains 1625AHL Operator Manual
(21 pages)
(100 pages)© 2020, manymanuals.com. All rights reserved. | 1.177 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals