Great-plains 1625AHL Operator Manual User Manual Page 46
- Page / 176
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
42 1625AH Table of Contents Index Great Plains Manufacturing, Inc.
411-020M Table of Contents Index 2014-04-21
Prepare Meter Doors
Material and Time Loss Risk:
Check the doors before loading, every time. If the Clean-Out
door is open, even slightly, it will be essentially impossible to
close adequately with material loaded.
Refer to Figure 30
8. Verify that both doors at the bottom of the central
hopper meter are tightly closed. After long storage,
they are commonly tied slightly closed, to allow
drainage of condensation and to avoid permanently
compressing the door seals. The doors must be fully
closed for loading and field operations.
If the hopper is empty, Great Plains advises opening
both doors, wiping down the meter lips and door
seals, then fully closing both doors.
Load Fertilizer
Add dry fertilizer to the hopper.
Do not fill above the 3500 L (100 BU.) mark.
Use only granular dry fertilizer.
Do not add liquid treatments.
Lid Closing
Refer to Figure 31
1. Swing lid over opening until capture hook is
centered on U-bolt.
2. Open handle and engage hook on U-bolt.
3. Close handle for operations or short-term parking.
For long-term storage, do not engage hook or latch
handle, to avoid deforming the seal.
4. For storage, particularly unlatched, a padlock
through both U-bolts deters unauthorized lid
opening, preventing entry of pests, debris and
precipitation.
Close walkboard rail section if opened for auger material
loading.
Monitor Operation
For monitor operation in the field, refer to the
DICKEY-john
®
PM400 Console Manual or
DICKEY-john
®
IntelliAg
®
MVT Manual supplied with this
unit, and the Seed Rate manual.
Figure 30
Central Hopper Meter Doors
34449
Figure 31
Hopper Lid Relatching
32455
2
3
3
2 3
2
- Operator 1
- Table of Contents 3
- Important Safety Information 5
- Handle Chemicals Properly 7
- Keep Riders Off Machinery 7
- Use Safety Lights and Devices 7
- Transport Machinery Safely 8
- Shutdown and Storage 8
- Tire Safety 8
- Practice Safe Maintenance 9
- Safety At All Times 9
- Safety Decals 10
- Amber Reflectors 11
- 838-267C 11
- Daytime Reflectors 11
- 838-265C 11
- 818-323C (Option) 12
- Danger: Chemical Hazard 12
- 818-590C 12
- Danger: Crushing Hazard 12
- EXCESSIVE SPEED HAZARD 14
- 818-632C 16
- Warning: Fan Hazard 16
- 818-860C 16
- Warning: Moving Parts 16
- 818-398C 18
- Caution: Tires Not A Step 18
- 838-426C 18
- Caution: Tire Pressure 18
- 858-011C 19
- Introduction 20
- Using This Manual 21
- Document Family 21
- Owner Assistance 21
- Preparation and Setup 22
- Hitching Tractor to Planter 23
- Hydraulic Hose Hookup 24
- Monitor Setup 26
- Marker Setup (Option) 27
- Operating Instructions 28
- Unfolding the Planter 30
- Raising/Lowering Planter 33
- Folding the Planter 34
- Install Lock Channels 35
- Activate Fold Solenoid Valves 35
- Begin Folding 35
- Transporting 37
- Transport Weights 38
- Loading Materials 39
- Monitor Operation 46
- Ground Drive Lock-Up 47
- Seed Meter Drive Lock-Up 49
- Field Setup Checklist 50
- Air System Operation 52
- Meter Operation 54
- Fan Operation 55
- 858-193C 56
- 848-020C 57
- Figure 45 60
- Dry Fertilizer System 62
- Liquid Fertilizer Operation 64
- Dry Fertilizer Operation 64
- Marker Operation 65
- Field Operation 66
- Adjustments 69
- Setting Material Rates 70
- Marker Adjustments 72
- Row Implement Adjustments 73
- 362363196 75
- SHARP OBJECT HAZARD 77
- Depth of (new) coulter blade 78
- Side Gauge Wheel Adjustment 81
- Row Unit Shut-Off 87
- Troubleshooting 92
- Seed Pool Troubleshooting 93
- Population Too Low 95
- Seed Population Too High 97
- Population Related 99
- Problem Cause Solution 100
- No Fertilizer 100
- General Troubleshooting 102
- Maintenance and Lubrication 105
- Height Switch Adjustment 106
- Material Clean-Out 107
- Dry Fertilizer Clean-Out 110
- Liquid Fertilizer Clean-Out 114
- Liquid Fertilizer Maintenance 115
- Seed Meter Maintenance 116
- Bleeding Hydraulics 119
- Marker Maintenance 120
- Chain Maintenance 121
- Per Hopper 124
- Caster Wheel Pivot 128
- As Required 129
- Seasonal 130
- Seed Lubricants 132
- Options and Accessories 133
- Frame-Mounted Row Accessories 134
- Row Options (Unit-Mount) 135
- Rigid Row Cleaners (UMRC) 136
- Seed Meter Disks 137
- Inside Disc Scrapers 137
- Gauge Wheel Scrapers 138
- Lock-Up Pins 138
- Seed Tube Brush 138
- Seed Firmers 139
- Paddle Wheel Kit 140
- Seed Lubricant 140
- Specifications and Capacities 141
- 47 feet 7 inches (14.50 m) 144
- Torque Values Chart 149
- Tire Inflation Chart 149
- Chain Routing 150
- Appendix B - Pre-Delivery 154
- 803-021C NUT HEX 5/8-11 PLT 155
- Marker Assembly 156
- 803-019C NUT LOCK 1/2-13 PLT 157
- Press Wheel Installation 158
- Appendix C - Initial Setup 160
- PM400 Monitor Quick-Start 161
- Level Planter 163
- Wing Alignment 164
- Speed Calibration 165
- Marker Extension 165
- 122-278S Scraper Installation 167
- Table of Contents Index 175
- Salina, Kansas 67402-5060 USA 176
Related products and manuals for Gardening equipment Great-plains 1625AHL Operator Manual
(21 pages)
(100 pages)© 2020, manymanuals.com. All rights reserved. | 1.158 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals