Great-plains 2525P Operator Manual User Manual Page 23
- Page / 159
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4/23/2010
118-915M
21
Operating Instructions
Field Operation
You may be severely injured or killed by being crushed
between the tractor and drill. Do not stand or place
any part of your body between drill and moving trac-
tor. Stop tractor engine and set park brake before in-
stalling pins.
1. Hitch drill to a suitable tractor or hitch. Refer to
“Hitching Tractor to Drill,” page 15 or your
hitch operator’s manual.
Refer to Figure 13
2. Make sure proper seed meter wheels are in
place. For information on how to change the
seed meter wheels see page 37.
Refer to Figure 14
3. Make sure all seed meter clean out doors are
closed and pinned. For more information see
page 35.
4. Set seeding rate as explained in “Seeding
Rate”, page 32.
Refer to Figure 15
5. Open and pin sliding seed tubes. For further
information see page 34.
6. Load box with clean seed and talc.
7. Raise drill. Rotate gauge wheel. Check that
seed meters, seed tubes and drives are work-
ing properly and free from foreign material by
looking for seed flow under each opener.
8. Record acremeter readout. Subtract initial
reading from later readings to determine
acres drilled.
9. Pull forward, lower drill and begin seeding.
10. Always lift drill out of the ground when turning
at row ends and for other short-radius turns.
Seeding will stop automatically as drill is
raised.
Figure 13
Seed meter wheel in place
Seed
meter
wheel
22851
Figure 14
Seed meter clean out door in closed position
18261
Seed meter
clean out door
Retaining
clip
Figure 15
Sliding seed tubes in open position
22852
Sliding seed
tubes
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 838-266C 9
- 818-003C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Using This Manual 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 22
- Field Operation 23
- Figure 16 24
- Seed Meter 24
- Transporting 25
- Figure 17 26
- Ladder Folded for Transport 26
- Adjustments 27
- 20 Series Openers 28
- 25 Series Openers 30
- Frame Height 34
- Seeding Rate 35
- Figure 42 36
- Figure 43 36
- Figure 44 36
- Figure 48 38
- Changing Seed Meter Wheel for 39
- Spin wheel 40
- Changing Seed Meters for 25 42
- Series Openers 42
- Figure 62 43
- Figure 63 43
- Figure 61 43
- Figure 64 44
- Figure 65 44
- Figure 69 46
- Figure 70 46
- Hole for 46
- 3 (number of meters measured) 47
- Tire Revolutions Per Acre 48
- Marker Adjustments 50
- Figure 75 52
- Adjusting Marker Carrier 52
- Shear Bolt 52
- Figure 74 52
- Marker Chain Adjustment 52
- Figure 76 53
- Marker Width Adjustment 53
- Seed-Lok™ Lock Up 55
- Troubleshooting 56
- Maintenance and Lubrication 62
- Figure 89 66
- Finger Meter 66
- Seed Tube Maintenance 67
- Figure 93 68
- Side Wheels 68
- Figure 92 68
- Drive Chains and Idlers 68
- Figure 94 69
- Opener Disks Contact Point 69
- Figure 95 69
- Disk Spreader 69
- Spreaders and Scrapers 70
- Figure 97 70
- Figure 96 70
- Figure 98 71
- Figure 99 71
- Figure 100 72
- Marker Shear Bolt 72
- Lubrication 73
- Seasonally 74
- Seed-Lok™ Firming Wheels 75
- Depth Wheel Scraper 76
- Baffle Kit 76
- DICKEY-john 76
- Monitor 76
- Veris Drive 77
- Weight Bracket Kit 77
- Keeton Seed Firmer 77
- Tractor Hookup 79
- Console Functions 81
- Calibration 81
- Figure 105 82
- Figure 106 82
- Figure 107 82
- Figure 108 83
- Figure 109 83
- Figure 110 83
- Figure 111 84
- Figure 112 84
- Figure 113 84
- Figure 114 85
- Figure 115 85
- Figure 116 85
- Figure 117 86
- Figure 118 86
- Figure 119 86
- Figure 120 87
- Figure 121 87
- Operations 88
- Veris Drive Sprocket Change 89
- GPS-Based Seeding 92
- 9 pin serial cable 94
- Maintenance 96
- Troubleshooting Flow Chart 100
- 4/23/2010 101
- 118-915M 101
- Seed Rate Charts 102
- 2525P and 2520P 104
- Seed Rate Application 133
- Charts for Finger Meter 133
- Sprocket Indexing Charts 145
- Appendix 154
- Tire Inflation Chart 155
- Specifications and Capacities 155
- Warranty 158
- Salina, Kansas 67402-5060 USA 159
Related products and manuals for Gardening equipment Great-plains 2525P Operator Manual
(11 pages)
(42 pages)
(40 pages)© 2020, manymanuals.com. All rights reserved. | 0.156 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals