Great-plains 2525P Operator Manual User Manual Page 89
- Page / 159
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4/23/2010
118-915M
87
Veris Drive Operating Instructions
Veris Drive Sprocket Change
For proper operation on finger meters (high range) it will
be necessary to switch from 12 tooth to 24 tooth Veris
Drive sprocket.
Refer to Figure 124
1. Loosen chain idler. Remove Veris drive chain. Pull
retaining clip from sprocket spacer (1). Remove
spacer (1) from Veris drive shaft.
2. Slide 12 tooth sprocket (2) and 24 tooth sprocket (3)
towards Veris drive until they rest against inside
locking collar (4).
3. Replace spacer (1) on shaft between 24 tooth
sprocket (3) and outside locking collar (5). Hold
spacer in place with retaining clip. Install Veris drive
chain and tighten chain idler.
4. Reverse this procedure to switch back to 12 tooth
sprocket (2) when operating 20 and 25 series
meters.
NOTE: Make sure and switch to proper sprocket on
both drives.
Calibration Table-Finger Meter (High Range)
Motor 24T Driver-Mainshaft 36T Driven
** Refer to seed chart to determine optimum planting speed for your nominal rate.
NOTE: Finger Meters require 24 tooth sprocket on Veris drive. Refer above for sprocket change.
Figure 124
Veris Drive Sprocket Change
Crop Row Spacing Number of cells Min. Rate Max. Rate Cal #
Corn 20” 6 Finger Meter 13200 35800 750***
Corn 20” 12 Finger Meter 17500 47700 1501**
Corn 30” 6 Finger Meter 8800 24000 500***
Corn 30” 12 Finger Meter 17500 47700 1000**
Corn 38” 6 Finger Meter 9200 21000 395***
Corn 38” 12 Finger Meter 28000 50000 790**
Corn TR 30” 6 Finger Meter 17500 47500 1000**
Corn TR 30” 12 Finger Meter 35000 96000 2001**
Corn TR 38” 6 Finger Meter 18500 50000 790***
Corn TR 38” 12 Finger Meter 28000 80000 1580**
1. Press Engage key to activate drive. Green light
above Engage key will illuminate.
NOTE: If you do not move within 10 seconds, the
automatic disengagement feature will disengage
the drive. To begin planting again, you must press
the Engage key.
2. Console display shows two numbers while operat-
ing: “Set” rate is the rate you tell the system to
plant, and the “Out” rate is the calculated rate
based on the actual rotations of the drive. The
“Out” reading is monitoring the drive system;it
isn’t monitoring population. It verifies that the drive
system is functioning properly.
Note: The “Out” readings will normally fluctuate within
5% of the “Set” rates. This fluctuation is evidence of
the drive system compensating for minor fluctuations
in ground speed.
3. If “Out” rate varies from the “Set” rate by more than
20%, an audible alarm will sound.
4. If Controller is powered directly from battery or un-
switched power port, make sure to power Console
off when tractor is shut down. This prevents tractor
battery drain.
22880
*** Extremely high rates on wide row spacing may require lower ground speed - refer to seed charts for mph limits.
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 838-266C 9
- 818-003C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Using This Manual 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 22
- Field Operation 23
- Figure 16 24
- Seed Meter 24
- Transporting 25
- Figure 17 26
- Ladder Folded for Transport 26
- Adjustments 27
- 20 Series Openers 28
- 25 Series Openers 30
- Frame Height 34
- Seeding Rate 35
- Figure 42 36
- Figure 43 36
- Figure 44 36
- Figure 48 38
- Changing Seed Meter Wheel for 39
- Spin wheel 40
- Changing Seed Meters for 25 42
- Series Openers 42
- Figure 62 43
- Figure 63 43
- Figure 61 43
- Figure 64 44
- Figure 65 44
- Figure 69 46
- Figure 70 46
- Hole for 46
- 3 (number of meters measured) 47
- Tire Revolutions Per Acre 48
- Marker Adjustments 50
- Figure 75 52
- Adjusting Marker Carrier 52
- Shear Bolt 52
- Figure 74 52
- Marker Chain Adjustment 52
- Figure 76 53
- Marker Width Adjustment 53
- Seed-Lok™ Lock Up 55
- Troubleshooting 56
- Maintenance and Lubrication 62
- Figure 89 66
- Finger Meter 66
- Seed Tube Maintenance 67
- Figure 93 68
- Side Wheels 68
- Figure 92 68
- Drive Chains and Idlers 68
- Figure 94 69
- Opener Disks Contact Point 69
- Figure 95 69
- Disk Spreader 69
- Spreaders and Scrapers 70
- Figure 97 70
- Figure 96 70
- Figure 98 71
- Figure 99 71
- Figure 100 72
- Marker Shear Bolt 72
- Lubrication 73
- Seasonally 74
- Seed-Lok™ Firming Wheels 75
- Depth Wheel Scraper 76
- Baffle Kit 76
- DICKEY-john 76
- Monitor 76
- Veris Drive 77
- Weight Bracket Kit 77
- Keeton Seed Firmer 77
- Tractor Hookup 79
- Console Functions 81
- Calibration 81
- Figure 105 82
- Figure 106 82
- Figure 107 82
- Figure 108 83
- Figure 109 83
- Figure 110 83
- Figure 111 84
- Figure 112 84
- Figure 113 84
- Figure 114 85
- Figure 115 85
- Figure 116 85
- Figure 117 86
- Figure 118 86
- Figure 119 86
- Figure 120 87
- Figure 121 87
- Operations 88
- Veris Drive Sprocket Change 89
- GPS-Based Seeding 92
- 9 pin serial cable 94
- Maintenance 96
- Troubleshooting Flow Chart 100
- 4/23/2010 101
- 118-915M 101
- Seed Rate Charts 102
- 2525P and 2520P 104
- Seed Rate Application 133
- Charts for Finger Meter 133
- Sprocket Indexing Charts 145
- Appendix 154
- Tire Inflation Chart 155
- Specifications and Capacities 155
- Warranty 158
- Salina, Kansas 67402-5060 USA 159
Related products and manuals for Gardening equipment Great-plains 2525P Operator Manual
(11 pages)
(42 pages)
(40 pages)© 2020, manymanuals.com. All rights reserved. | 2.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals