Great-plains 2525P Operator Manual User Manual Page 67
- Page / 159
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4/23/2010
118-915M
65
Maintenance and Lubrication
Seed Tube Maintenance
Refer to Figure 90
Clean inner sliding seed tube if it will not slide. Re-
place inner sliding seed tube if you see any visible
cracks.
Sliding Seed Tube Replacement
Refer to Figure 91
To replace inner sliding seed tube, follow these
steps:
1. Make sure seed box is empty.
2. Loosen bottom clamp (1).
3. Pull inner sliding seed tube (2) out of seed
meter grommet and pull inner tube down and
out of outer sliding seed tube (3).
4. Inspect outer sliding seed tube for wear and
replace if necessary. Loosen top clamp (4)
and pull outer sliding seed tube from seed box
grommet.
5. Fit new outer sliding seed tube into seed box
grommet. The distance from seed box grom-
met lip to the top of the clamp should be no
more than 3/16 inch, see insert. The outer
sliding seed tube must extend above the rub-
ber grommet by 1/4” to 3/8” for 20 series
openers and by 1/2” to 5/8” for 25 series
openers, see insert. Tighten clamp (4).
6. Place new inner sliding seed tube inside outer
sliding seed tube. Make sure the chamfer on
the inside of the tube is up as shown.
7. Fit inner sliding seed tube into seed meter
grommet and tighten clamp.
8. Replace inner sliding seed tube inside outer
sliding seed tube as shown, fit into seed
meter grommet and tighten clamp (1).
18298
Outer sliding
seed tube
Inner sliding
seed tube
Figure 90
Figure 91
22834
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 838-266C 9
- 818-003C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Using This Manual 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 22
- Field Operation 23
- Figure 16 24
- Seed Meter 24
- Transporting 25
- Figure 17 26
- Ladder Folded for Transport 26
- Adjustments 27
- 20 Series Openers 28
- 25 Series Openers 30
- Frame Height 34
- Seeding Rate 35
- Figure 42 36
- Figure 43 36
- Figure 44 36
- Figure 48 38
- Changing Seed Meter Wheel for 39
- Spin wheel 40
- Changing Seed Meters for 25 42
- Series Openers 42
- Figure 62 43
- Figure 63 43
- Figure 61 43
- Figure 64 44
- Figure 65 44
- Figure 69 46
- Figure 70 46
- Hole for 46
- 3 (number of meters measured) 47
- Tire Revolutions Per Acre 48
- Marker Adjustments 50
- Figure 75 52
- Adjusting Marker Carrier 52
- Shear Bolt 52
- Figure 74 52
- Marker Chain Adjustment 52
- Figure 76 53
- Marker Width Adjustment 53
- Seed-Lok™ Lock Up 55
- Troubleshooting 56
- Maintenance and Lubrication 62
- Figure 89 66
- Finger Meter 66
- Seed Tube Maintenance 67
- Figure 93 68
- Side Wheels 68
- Figure 92 68
- Drive Chains and Idlers 68
- Figure 94 69
- Opener Disks Contact Point 69
- Figure 95 69
- Disk Spreader 69
- Spreaders and Scrapers 70
- Figure 97 70
- Figure 96 70
- Figure 98 71
- Figure 99 71
- Figure 100 72
- Marker Shear Bolt 72
- Lubrication 73
- Seasonally 74
- Seed-Lok™ Firming Wheels 75
- Depth Wheel Scraper 76
- Baffle Kit 76
- DICKEY-john 76
- Monitor 76
- Veris Drive 77
- Weight Bracket Kit 77
- Keeton Seed Firmer 77
- Tractor Hookup 79
- Console Functions 81
- Calibration 81
- Figure 105 82
- Figure 106 82
- Figure 107 82
- Figure 108 83
- Figure 109 83
- Figure 110 83
- Figure 111 84
- Figure 112 84
- Figure 113 84
- Figure 114 85
- Figure 115 85
- Figure 116 85
- Figure 117 86
- Figure 118 86
- Figure 119 86
- Figure 120 87
- Figure 121 87
- Operations 88
- Veris Drive Sprocket Change 89
- GPS-Based Seeding 92
- 9 pin serial cable 94
- Maintenance 96
- Troubleshooting Flow Chart 100
- 4/23/2010 101
- 118-915M 101
- Seed Rate Charts 102
- 2525P and 2520P 104
- Seed Rate Application 133
- Charts for Finger Meter 133
- Sprocket Indexing Charts 145
- Appendix 154
- Tire Inflation Chart 155
- Specifications and Capacities 155
- Warranty 158
- Salina, Kansas 67402-5060 USA 159
Related products and manuals for Gardening equipment Great-plains 2525P Operator Manual
(11 pages)
(42 pages)
(40 pages)© 2020, manymanuals.com. All rights reserved. | 0.166 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals