Great-plains 606NT Operator Manual User Manual Page 18
- Page / 80
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
151-061M Table of Contents Index 2014-02-10
14 3P605NT, 3P606NT, 605NT & 606NT Table of Contents Index Great Plains Manufacturing, Inc.
Preparation and Setup
This section helps you prepare your tractor and drill for
use. Before using the drill in the field, you must hitch the
drill to a suitable tractor and also setup the drill.
Pre-Setup Checklist
1. Verify that dealer pre-delivery is complete (page 67)
and optional accessories are installed (page 68).
2. Read and understand “Important Safety
Information” on page 1.
3. Check that all working parts are moving freely, bolts
are tight, and cotter pins are spread.
4. Check that all grease fittings are in place and
lubricated. See “Lubrication and Scheduled
Maintenance” on page 48.
5. Check that all safety decals and reflectors are
correctly located and legible. Replace if damaged.
See “Safety Decals” on page 6.
6. Inflate tires and tighten wheel bolts as at “Tire
Pressures” on page 60.
Hitching Tractor to Drill
Hitching Model 3P605NT or 3P606NT
Crushing Hazard:
You may be severely injured or killed by being crushed
between the tractor and drill. Do not stand or place any part of
your body between drill and moving tractor. Stop tractor
engine and set park brake before installing the hitch pin.
Certain Machine Damage:
Remove tractor draw bar before hitching the 3P605NT or
3P606NT. The drill drive wheel will be damaged if drawbar is
not removed.
1. Raise or lower tractor 3-point arms as needed and
pin lower arms to drill.
2. Pin upper arm to drill.
3. Slowly raise drill. Watch for cab interference.
4. Adjust top 3-point link so the top edge of drill box is
parallel with the ground when drilling.
Note: Do not use link to adjust opener depth. For opener
adjustments, refer to “Opener Depth (Press
Wheel Height)” on page 38. Set your tractor
3-point draft control to Float position for planting.
Equipment Damage Risk:
Due to interference with the gauge wheel assembly, drill
models 3P605NT and 3P606NT are not compatible with
Great Plains accessory hitches CPH, PFH and SSH, nor with
the Great Plains hitch set-back kit.
- Operator Manual 1
- Table of Contents Index 2
- Table of Contents 3
- Important Safety Information 5
- Wear Protective Equipment 6
- Handle Chemicals Properly 6
- Avoid High Pressure Fluids 6
- Use an Adequate Tractor 7
- Use A Safety Chain 7
- Keep Riders Off Machinery 7
- Use Safety Lights and Devices 7
- Transport Machinery Safely 8
- Shutdown and Storage 8
- Tire Safety 8
- Practice Safe Maintenance 9
- Safety At All Times 9
- Safety Decals 10
- MOVING CHAIN HAZARD 11
- Warning: Speed 12
- Warning: High Pressure Fluid 12
- 838-102C 13
- Caution: Tires Not A Step 14
- Caution: General 14
- 848-021C REV. B 15
- Introduction 16
- Using This Manual 17
- Owner Assistance 17
- Preparation and Setup 18
- Hitching Model 605NT or 606NT 19
- Electrical Connections 20
- Height and Leveling the Drill 21
- Operation Instructions 23
- Transporting 605NT or 606NT 25
- Loading Seed 28
- Field Operation 29
- Acremeter Operation 30
- Adjustments 33
- Frame Weight Adjustment 34
- Coulter Adjustments 35
- 10.0 inches 36
- Opener Spring 38
- Disc Scraper Adjustment 40
- Troubleshooting 43
- Acremeter inaccurate 45
- Problem Cause Solution 45
- Maintenance and Lubrication 46
- Seed Flap Replacement 49
- Bleeding Hydraulics 50
- Drive Shaft Clutch 53
- Seed Cup Drive Shaft Sprocket 53
- Gauge Wheel Arms 53
- As Required 54
- Seasonal 55
- Acremeter 57
- Calibration Kits 57
- Carbide Disc Scraper 58
- Coulter Blades 58
- Grease Bank 58
- Main Seed Box Accessories 59
- Seed Lubricants 60
- Native Grass Rate Reduction 60
- Press Wheel Selection 61
- Small Seeds Attachment 61
- Seed Firmers 62
- Weight Brackets 63
- Specifications and Capacities 64
- Tire Pressures 64
- Torque Values Chart 65
- To Tractor 66
- Drive System Diagrams 67
- 605NT and 606NT Drives 68
- Appendix B - Pre-Delivery 71
- Warranty 73
- Salina, Kansas 67402-5060 USA 80
Related products and manuals for Gardening equipment Great-plains 606NT Operator Manual
(10 pages)
(38 pages)© 2020, manymanuals.com. All rights reserved. | 0.255 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals