Great-plains DVN8324 Assembly Manual User Manual Page 18
- Page / 74
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
14 8315-8324DVN Great Plains Manufacturing, Inc.
550-466Q-ENG 11/25/2013
Refer to Figure 9
Install 8324 Wings
Note: To install wings, it would be best to have the wing
frames 180 degrees in relation to the center frame.
Installing wing frames with the 90 degree relation
to center can be difficult. If wings are installed 90
degrees to center, be sure to install the lift cylin-
ders and hoses with black handles (as shown on
page15-18) to raise center frame so the tire does
not interfere with unfolding the wing.
43. Carefully align holes in wing frame LH with holes
in center frame. Secure with 1 x 7, Gr. 8 hex bolt
and 1 nylon lock nut.
• Be sure and install the 1 x 7, Gr. 8 hex bolts as
shown with head against plate on side of hinge.
44. Attach wing brace LH to wing frame LH with 3/4
x 2 hex bolts , 3/4 lock washers and 3/4 hex nuts.
45. Install 1 x 7, Gr. 8 hex bolts and 1 nylon lock nuts
through hinge in center wing brace.
46. Align holes in wheel arm L , secure with 1 1/4 x 6
pin , 3/8 x 2 1/4 Gr. hex bolts and 3/8 top lock
nuts.
47. Align hole in 8-bolt spindle assembly , secure with
5/16 x 4, Gr. 8 hex bolt 5/16 lock washer and 5/16
hex nut.
48. Attach tire/wheel assembly with 5/8 lug nuts .
49. Attach 1 1/4 x 9 1/2 eye bolt , secure with 1 1/4
jam nut (one on each side plate).
50. Mount 3.25 x 8 x 1.25 cylinder to eye bolt and
wheel arm L with1x31/8pins , 1.5 x 1.0 x.075
machine washers and 3/16 x 2 cotter pins.
51. Mount rocker bracket to wing plate with 3/4 x 3
hex bolts , 3/4 lock washers and 3/4 hex nuts.
a.Attach one end of rocker to rocker bracket
using 1 x 3 3/8 pin , 1.5 x 1.0 x.075 machine
washer and 3/16 x 2 cotter pin.
b. Mount stub to wing frames with 3/4 x 2 hex
bolts , 3/4 lock washers and 3/4 hex nuts.
c. Attach one end of connecting link to rocker
bracket ) and other end to stub with 1 x 3 hex
bolts , 1 lock washers and 1 nuts.
52. Repeat same procedure for right wing.
53. Attach 4 x 36 x 1.5 cylinders with 1 x 3 1/8 pins
, 1.5 x 1.0 x.075 machine washers and 3/16 x 2
cotter pins.
54. Attach valve plate to front tube of center wing
brace with 1/2 x 3 1/32 x 5 u-bolt , 1/2 lock wash-
ers and 1/2 nuts.
55. Attach lock valve to valve plate with 1/4 x 1 1/4
x 2 u-bolts , 1/4 lock washers and 1/4 nuts.
56. Tighten all bolts to specs, See “Torque Values
Chart” on page 37.
1
2
2
3 1
4
2
5
6 7
8
9
10
11
12
13
14 12
5
15
16
17
18 16
19
20
1
4
21
16 20
22
23
15
24
25
26 24
27
- Assembly Manual 1
- Table of Contents Index 2
- Table of Contents 3
- 550-466Q-ENG 11/25/2013 4
- Important Safety Information 5
- Wear Protective Equipment 6
- Avoid High Pressure Fluids 6
- Use Safety Lights and Devices 6
- Keep Riders Off Machinery 6
- Shutdown and Storage 7
- Tire Safety 7
- Safety At All Times 7
- Introduction 8
- Using This Manual 9
- Shipping Inventory 10
- Unloading 10
- Assembly 11
- Truss & Level Bar 12
- Assembly 9 13
- Figure 6 13
- Connect Hitch 14
- Figure 7 15
- Hitch Assembly 15
- Assembly 11 15
- Install 8315-8321 Wings 16
- Assembly 13 17
- Figure 8 17
- 8315-8321 Wing Assembly 17
- Install 8324 Wings 18
- Assembly 15 19
- Figure 9 19
- 8324 Wing Assembly 19
- Install K-Flex 20
- Install Magnum Shank 20
- Install Gang Hangers 21
- Install Hydraulic Valves 22
- Hydraulic Hose Hookup 24
- Hose Handles 25
- Purging Hydraulic System 25
- Install Gang Assembly 26
- Install Depth Guide Decal 27
- North American Light Assembly 28
- Assembly 25 29
- Figure 24 29
- North American Lights 29
- International Lights Assembly 30
- Assembly 27 31
- Figure 25 31
- International Lights 31
- Air Brakes Assembly 32
- Assembly 29 33
- Figure 26 33
- Air Brakes 33
- Hydraulic Brakes Assembly 34
- Assembly 31 35
- Figure 27 35
- Hydraulic Brakes 35
- Retract Assembly 36
- Assembly 33 37
- Figure 28 37
- Retract Kit 37
- Connect Wiring Harness 38
- Install Rear Hitch (optional) 39
- Completing Setup 40
- Appendix 41
- Tire Inflation Chart 42
- Appendix 39 43
- Fold Hydraulic Layout 44
- Retract Layout 45
- 8315D Machine Layout, Disc 46
- 8315C Machine Layout, Coulter 47
- 8318D Machine Layout, Disc 48
- 8318C Machine Layout, Coulter 49
- 8321D Machine Layout, Disc 50
- 8321C Machine Layout, Coulter 51
- 8324D Machine Layout, Disc 52
- 8324C Machine Layout, Coulter 53
- 8315DVN S7T Layout 55
- 8315DVN S5T HR Layout 56
- 8315DVN CH4B Coil Tine Layout 57
- 8318DVN S7T Layout 59
- 8318DVN S5T HR Layout 60
- 8318DVN CH4B Coil Tine Layout 61
- 8321DVN S7T Layout 63
- 8321DVN S5T HR Layout 64
- 8321DVN CH4B Coil Tine Layout 65
- 8324DVN S7T Layout 67
- 8324DVN S5T HR Layout 68
- 8324DVN CH4B Coil Tine Layout 69
- 11/25/2013 550-466Q-ENG 71
- Numerics 72
- Salina, Kansas 67402-5060 USA 74
Related products and manuals for Gardening equipment Great-plains DVN8324 Assembly Manual
(176 pages)
(224 pages)
(38 pages)© 2020, manymanuals.com. All rights reserved. | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals