Great-plains NTA2007HD Operator Manual User Manual Page 53
- Page / 178
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Great Plains Manufacturing, Inc. Contents Index Operating Instructions 49
04/04/2011 Contents Index 166-283M
Loading: Air-Out System
Refer to Figure 42
7. At each empty hopper to be loaded, if meter box
clean-out door or calibration was completely closed,
open it. See “Meter Doors” on page 46.
8. If any doors are fully or partially open, wipe seals
and meter bottom flanges clean. Close and latch
doors.
9. If the drill has been parked for more than a day, con-
densation may have caused moisture to accumulate.
Whether or not meter doors are opened, run the fan
system for several minutes to blow moisture out of
the meters, primary and secondary seed hoses.
10. With the fan running, check hopper-lid and meter-
box seals carefully for air leaks. Adjust bin latch or
replace seals to prevent leakage.
Loading: Prepare Hopper(s)
11. Shut off all hydraulic power to the drill (unless using
a tractor or cart circuit for an auger).
12. Open lid of hopper to be loaded (page 43).
13. Check that the strainer basket is in place in the top of
the bin. Remove any foreign material from basket.
Loading: Load Seed or Dry Fertilizer
14. Load material at open hopper lid.
15. Check the strainer periodically for foreign matter.
If markers are not installed on the implement, circuits
A&B are available at the left rear of the cart, and may be
used for auxiliary purposes, such as a user-provisioned
auger. Auger height required is:
3.0m (9.8 ft) for 5290 liter (150 bu) hopper, and
2.8m (9.3 ft) for 2890 liter (82 bu) hoppers
Loading: Close-Out
16. Remove any foreign matter from the strainer basket.
17. Wipe any grain or foreign matter from lid-seal area
on top of hopper bin. Close lid(s) and latch securely.
18. Return ladder to storage/transport position
(page 42).
Planning Re-Loads
The seed monitor has a level sensor in each hopper to
warn when seed box is empty. Alerts occur at these
approximate levels of remaining material:
82bu hopper: 25 liters (0.7 bu)
150bu hopper: 25 liters (0.7 bu).
Null4:
Figure 42
Close Meter Doors
31158
Material Mis-Application Risk:
Before filling the drill for the first time, and at the beginning of
each season, check the entire bin for leaks. A small air leak
can cause large variations in seeding rates.
Null4:
Null4:
Null4:
Entanglement and High Pressure Fluid Hazards:
Never operate an auger without guards. Wear gloves and eye
protection when making/breaking auger hydraulic connec-
tions. Follow all auger manufacturer instructions for safe
auger operation.
Figure 43
Cart Hydraulic Panel
848-562c
Marker
Circuit
Receptacles
(A & B)
- Operator Manual 1
- Contents Index ii 2
- Table of Contents 3
- Important Safety Information 5
- Wear Protective Equipment 6
- Use A Safety Chain 6
- Avoid High Pressure Fluids 6
- Minimize Radiation Exposure 6
- Handle Chemicals Properly 7
- Confined Space 7
- Tire Safety 8
- Use Safety Lights and Devices 8
- Keep Riders Off Machinery 8
- Transport Machinery Safely 8
- Shutdown and Storage 8
- Practice Safe Maintenance 9
- Safety At All Times 9
- Safety Decals 10
- Reflectors: Fluorescent Panels 11
- Reflectors: Red 11
- Reflectors: Daytime 12
- Reflectors: Amber 12
- Transport: Speed 13
- Danger: Read Manual 13
- Danger: Do Not Ride 14
- Danger: Crush (Marker Option) 14
- Danger: Electrocution 14
- Danger: Hitch Crushing 15
- Danger: Marker Crush (Option) 15
- Danger: Chemicals 15
- Danger: Chemicals (Option) 16
- Danger: Wing Crushing 16
- Danger: Marker Pinch (Option) 16
- Warning: Fan Hazard 17
- Warning: Moving Chain 17
- Warning: Wear Eye Protection 17
- Warning: Pinch Point 18
- Warning: High Pressure Fluid 18
- Warning: Confined Space 18
- Warning: Moving Gears 19
- Warning: Falling Hazard 19
- Warning: Hand Pinch 20
- Caution: Read Operator Manual 20
- Caution: Radar in Use 20
- Caution: Use Adequate Tractor 22
- Caution: Tires Not A Step 22
- Introduction 23
- Owner Assistance 24
- Preparation and Setup 25
- Hitching Tractor to Air Drill 26
- Hydraulic Hose Hookup 27
- Brake Hookup (Option) 28
- Air Brake Hookup 29
- Hydraulic Brake Hookup 29
- Electrical Hookup 30
- Heights and Leveling 30
- Marker Setup 31
- Operating Instructions 33
- Unfolding and Folding 34
- Unfold: Summary of Steps 35
- Fold: Summary of Steps 37
- Lowering 40
- Transporting the Air Drill 42
- Tractor Requirements 43
- Transport Checklist 43
- Brake Operation (option) 44
- Service Brake Operation 45
- Ladder Operations 46
- Hopper Lid Operation 47
- Lid Closing 48
- Tank Lid Operation 49
- Meter Doors 50
- Loading Materials 51
- 848-562c 53
- Operating the Hand Crank 56
- Air System Operation 58
- Air Systems Overview 59
- Fan Operation 60
- Marker Operation (Option) 62
- Marker Safety Information 63
- Marker Unfold and Fold 63
- Field Operations 64
- Field Operation 65
- Unfolded Storage 67
- Adjustments 68
- Setting Material Rates 69
- Find Your Chart and Rate 70
- Monitor Material Configuration 71
- MetaData: Wheat 73
- MetaData: 2S 73
- Meter Rate Adjustment 75
- Meter Calibration 77
- Calibration Crank Revolutions 79
- Parameter Value Comment 82
- Planting Depth Adjustments 84
- Adjusting Tool Bar Height 85
- Air System Adjustments 86
- Adjusting Fan Speed 87
- Diverter Vane Adjustments 88
- Weight Transfer Adjustments 89
- Frame-Mounted Coulters 91
- Frame-Mounted Coulter Force 92
- 07HD Row Unit Adjustments 93
- Row Unit Spring Adjustment 94
- Disk Blade Adjustments 94
- Disk Scraper Adjustments 95
- Seed Firmer Adjustments 96
- Fertilizer Tube Adjustment 97
- Marker Adjustments 98
- Marker Extension Adjustment 99
- Marker Speed 100
- Marker Disk Adjustment 100
- Troubleshooting 101
- Problem Causes Solutions 102
- Lift Lock Troubleshooting 104
- Problem Cause Solution 107
- Maintenance and Lubrication 108
- Maintenance Lift Lock 109
- Hopper Strap Maintenance 110
- Chain Maintenance 110
- Maintenance 110
- Fertilizer System Maintenance 111
- Unloading Materials 112
- Material Clean-Outs 113
- Problem Clean-Outs 114
- Hopper Entry 114
- Contact Drive Re-setting 117
- Hydraulic Maintenance 118
- In-Line Filter 121
- Brake Maintenance (Option) 122
- Brake Line Charge and Bleed 123
- Air Brake Maintenance 125
- Brake Shoe Replacement 127
- Brake Drum Maintenance 131
- Mounting Wheels 132
- Test and Adjust Brakes 132
- Leveling Implement 133
- Marker Maintenance (Option) 134
- Seed Flap Replacement 135
- 0, 1, 10, 50 136
- Cart-Implement Link 137
- Rear Lower Parallel Arms 137
- Rear Upper Parallel Arms 138
- Coulter Pivots 138
- As Required 139
- Seasonal 142
- Variable Rate Kit 145
- High Rate Flute Sets 145
- Tramline 146
- Row Options 146
- Opener Disk Scraper 147
- Seed Firmers 147
- Specifications and Capacities 148
- Contents Index 04/04/2011 150
- Tire Inflation Chart 151
- Torque Values Chart 152
- Chain Routing 153
- Figure 132 154
- Contents Index 166-283M 155
- Figure 133 155
- Figure 134 156
- Hydraulic Diagrams 157
- Figure 136 158
- Cart Hydraulic Schematic 158
- Fold/Weight/Lock Hydraulics 159
- Figure 138 160
- Lift Hydraulics 161
- Marker Hydraulics (Option) 162
- Figure 141 163
- Air Over Hydraulic Brakes 163
- Hydraulic Brakes (Option) 164
- Fertilizer Plumbing (Option) 165
- Appendix B - Initial Setup 166
- Changing Meter Flutes 167
- Scraper Installation 168
- Warranty 169
- Cover Contents 04/04/2011 176
- Contents Index 173 177
- Salina, Kansas 67402-5060 USA 178
Related products and manuals for Gardening equipment Great-plains NTA2007HD Operator Manual
(87 pages)
(46 pages)© 2020, manymanuals.com. All rights reserved. | 2.002 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals