Great-plains NTA2007HD Operator Manual User Manual Page 85
- Page / 178
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Great Plains Manufacturing, Inc. Contents Index Adjustments 81
04/04/2011 Contents Index 166-283M
Adjusting Tool Bar Height
Refer to Figure 66
See “Heights and Leveling” on page 26 for how to
check tool bar height. To change the tool bar height, add
or remove master lift cylinder rod spacers , in the com-
binations shown in the chart at the bottom of this page.
To change spacers:
1. Perform a Lift operation (page 36).
2. Add or remove spacers. Unused spacers are stored
on rods loops welded to the cart-implement link (not
visible in figure). If you store spacers on hoses, make
sure they cannot slide into locations where they
interfere with implement operation.
Note: Chart values are approximate. Press wheel set-
tings, disk wear and manufacturing tolerances can
cause actual heights and depths to vary from chart
values. Choose spacer combinations based on ac-
tual field measurements.
Note: The cylinder has 5.7cm (2
1
⁄
4
in) of exposed rod
when fully retracted, for a minimum tool bar height
of 58.4cm (23.0in). All spacer combinations that
increase tool bar height above the minimum must
be a stack of at least 5.7cm in height.
Note: Each full (1)cm or (1)inch of spacer stack height
change changes the tool bar height by 2cm or 2in.
Note: Do not use a spacer stack taller than 10.2cm
(4.0in), or the furrow will be too shallow, or there will
be no furrow at all.
Null4:
Figure 66
Spacers for Tool Bar Height
31226
1
1
2
1
Spacers Used
10.2 cm (4.00 in) 11.4 cm (4.50 in) 58.4 cm (23.0 in) 5.7 cm (2.25 in) X X
8.9 cm (3.50 in) 10.2 cm (4.00 in) 59.7 cm (23.5 in) 6.4 cm (2.50 in) X X
7.6 cm (3.00 in) 8.9 cm (3.50 in) 61.0 cm (24.0 in) 7.0 cm (2.75 in) X X
6.4 cm (2.50 in) 7.6 cm (3.00 in) 62.2 cm (24.5 in) 7.6 cm (3.00 in) X X X
5.1 cm (2.00 in) 6.4 cm (2.50 in) 63.5 cm (25.0 in) 8.3 cm (3.25 in) X X X
3.8 cm (1.50 in) 5.1 cm (2.00 in) 64.8 cm (25.5 in) 8.9 cm (3.50 in) X X X
2.5 cm (1.00 in) 3.8 cm (1.50 in) 66.0 cm (26.0 in) 9.5 cm (3.75 in) X X X
1.3 cm (0.50 in) 2.5 cm (1.00 in) 67.3 cm (26.5 in) 10.2 cm (4.00 in) X X X
Maximum
Opener
Depth
Maximum
Coulter
Depth
Tool
Bar
Height
Spacer
Stack
Height
5.1 cm
(2.00 in)
3.8 cm
(1.50 in)
3.2 cm
(1.25 in)
2.5 cm
(1.00 in)
1.9 cm
(0.75 in)
- Operator Manual 1
- Contents Index ii 2
- Table of Contents 3
- Important Safety Information 5
- Wear Protective Equipment 6
- Use A Safety Chain 6
- Avoid High Pressure Fluids 6
- Minimize Radiation Exposure 6
- Handle Chemicals Properly 7
- Confined Space 7
- Tire Safety 8
- Use Safety Lights and Devices 8
- Keep Riders Off Machinery 8
- Transport Machinery Safely 8
- Shutdown and Storage 8
- Practice Safe Maintenance 9
- Safety At All Times 9
- Safety Decals 10
- Reflectors: Fluorescent Panels 11
- Reflectors: Red 11
- Reflectors: Daytime 12
- Reflectors: Amber 12
- Transport: Speed 13
- Danger: Read Manual 13
- Danger: Do Not Ride 14
- Danger: Crush (Marker Option) 14
- Danger: Electrocution 14
- Danger: Hitch Crushing 15
- Danger: Marker Crush (Option) 15
- Danger: Chemicals 15
- Danger: Chemicals (Option) 16
- Danger: Wing Crushing 16
- Danger: Marker Pinch (Option) 16
- Warning: Fan Hazard 17
- Warning: Moving Chain 17
- Warning: Wear Eye Protection 17
- Warning: Pinch Point 18
- Warning: High Pressure Fluid 18
- Warning: Confined Space 18
- Warning: Moving Gears 19
- Warning: Falling Hazard 19
- Warning: Hand Pinch 20
- Caution: Read Operator Manual 20
- Caution: Radar in Use 20
- Caution: Use Adequate Tractor 22
- Caution: Tires Not A Step 22
- Introduction 23
- Owner Assistance 24
- Preparation and Setup 25
- Hitching Tractor to Air Drill 26
- Hydraulic Hose Hookup 27
- Brake Hookup (Option) 28
- Air Brake Hookup 29
- Hydraulic Brake Hookup 29
- Electrical Hookup 30
- Heights and Leveling 30
- Marker Setup 31
- Operating Instructions 33
- Unfolding and Folding 34
- Unfold: Summary of Steps 35
- Fold: Summary of Steps 37
- Lowering 40
- Transporting the Air Drill 42
- Tractor Requirements 43
- Transport Checklist 43
- Brake Operation (option) 44
- Service Brake Operation 45
- Ladder Operations 46
- Hopper Lid Operation 47
- Lid Closing 48
- Tank Lid Operation 49
- Meter Doors 50
- Loading Materials 51
- 848-562c 53
- Operating the Hand Crank 56
- Air System Operation 58
- Air Systems Overview 59
- Fan Operation 60
- Marker Operation (Option) 62
- Marker Safety Information 63
- Marker Unfold and Fold 63
- Field Operations 64
- Field Operation 65
- Unfolded Storage 67
- Adjustments 68
- Setting Material Rates 69
- Find Your Chart and Rate 70
- Monitor Material Configuration 71
- MetaData: Wheat 73
- MetaData: 2S 73
- Meter Rate Adjustment 75
- Meter Calibration 77
- Calibration Crank Revolutions 79
- Parameter Value Comment 82
- Planting Depth Adjustments 84
- Adjusting Tool Bar Height 85
- Air System Adjustments 86
- Adjusting Fan Speed 87
- Diverter Vane Adjustments 88
- Weight Transfer Adjustments 89
- Frame-Mounted Coulters 91
- Frame-Mounted Coulter Force 92
- 07HD Row Unit Adjustments 93
- Row Unit Spring Adjustment 94
- Disk Blade Adjustments 94
- Disk Scraper Adjustments 95
- Seed Firmer Adjustments 96
- Fertilizer Tube Adjustment 97
- Marker Adjustments 98
- Marker Extension Adjustment 99
- Marker Speed 100
- Marker Disk Adjustment 100
- Troubleshooting 101
- Problem Causes Solutions 102
- Lift Lock Troubleshooting 104
- Problem Cause Solution 107
- Maintenance and Lubrication 108
- Maintenance Lift Lock 109
- Hopper Strap Maintenance 110
- Chain Maintenance 110
- Maintenance 110
- Fertilizer System Maintenance 111
- Unloading Materials 112
- Material Clean-Outs 113
- Problem Clean-Outs 114
- Hopper Entry 114
- Contact Drive Re-setting 117
- Hydraulic Maintenance 118
- In-Line Filter 121
- Brake Maintenance (Option) 122
- Brake Line Charge and Bleed 123
- Air Brake Maintenance 125
- Brake Shoe Replacement 127
- Brake Drum Maintenance 131
- Mounting Wheels 132
- Test and Adjust Brakes 132
- Leveling Implement 133
- Marker Maintenance (Option) 134
- Seed Flap Replacement 135
- 0, 1, 10, 50 136
- Cart-Implement Link 137
- Rear Lower Parallel Arms 137
- Rear Upper Parallel Arms 138
- Coulter Pivots 138
- As Required 139
- Seasonal 142
- Variable Rate Kit 145
- High Rate Flute Sets 145
- Tramline 146
- Row Options 146
- Opener Disk Scraper 147
- Seed Firmers 147
- Specifications and Capacities 148
- Contents Index 04/04/2011 150
- Tire Inflation Chart 151
- Torque Values Chart 152
- Chain Routing 153
- Figure 132 154
- Contents Index 166-283M 155
- Figure 133 155
- Figure 134 156
- Hydraulic Diagrams 157
- Figure 136 158
- Cart Hydraulic Schematic 158
- Fold/Weight/Lock Hydraulics 159
- Figure 138 160
- Lift Hydraulics 161
- Marker Hydraulics (Option) 162
- Figure 141 163
- Air Over Hydraulic Brakes 163
- Hydraulic Brakes (Option) 164
- Fertilizer Plumbing (Option) 165
- Appendix B - Initial Setup 166
- Changing Meter Flutes 167
- Scraper Installation 168
- Warranty 169
- Cover Contents 04/04/2011 176
- Contents Index 173 177
- Salina, Kansas 67402-5060 USA 178
Related products and manuals for Gardening equipment Great-plains NTA2007HD Operator Manual
(87 pages)
(46 pages)© 2020, manymanuals.com. All rights reserved. | 0.179 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals