Great-plains 2025P Operator Manual User Manual Page 20
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2025P, 2020P Bedded, and
2010HDP
118-928M
8/14/2006
18
20 Series Opener Dual Gauge Wheels
Refer to Figure 7
Initially adjust drill so bottom of opener tube runs
24 inches above ground when drill is lowered in
the field.
Refer to Figure 8
To adjust:
1. Loosen jam nut near top clevis of each
gauge-wheel turnbuckle.
NOTE: Jam nut is left-hand threaded.
2. Make sure upper clevis (2) is in upper mount
hole as shown.
3. Set turnbuckle length. Turn turnbuckle to
shorten or lengthen as necessary. Initially set
length to 17 1/2 inches between pin centers to
achieve the 24-inch dimension mentioned
above. When adjusting the turnbuckle length,
remember:
• Lengthening turnbuckle raises drill.
• Shortening turnbuckle lowers drill.
4. After adjusting both turnbuckles to the same
length, tighten jam nuts.
5. Level drill with top three-point link.
Refer to Figure 9
NOTE: When drill is level, parallel links will be
running slightly uphill towards the front.
The 1-inch dimension shown is a general dimen-
sion that will vary with planting conditions.
IMPORTANT: Make sure the opener mount is
running higher than the opener body. This will
ensure an ample reserve for opener upfloat in
case the opener strikes a rock or other object.
18280
Figure 7
Initial Operating Height
Figure 8
Gauge-Wheel Turnbuckle
22845
Figure 9
Leveling the Drill
18288
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 818-003C 9
- 838-266C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Left-hand 15
- Right-hand 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 23
- Field Operation 24
- Figure 16 25
- Seed Meter 25
- Transporting 26
- Figure 17 27
- Ladder Folded for Transport 27
- Adjustments 28
- 20 Series Openers 29
- 25 Series Openers 31
- HD 10 Series Openers 35
- Figure 42 37
- Double V Press Wheel 37
- Frame Height 39
- Seeding Rate 40
- Figure 49 41
- Figure 50 41
- Figure 1 41
- Figure 51 41
- Figure 55 43
- Changing Seed Meter Wheel for 44
- Spin wheel 45
- Series Openers and 25 Series 47
- Figure 69 48
- Figure 70 48
- Figure 68 48
- Figure 71 49
- Figure 72 49
- HD 10 Series Openers and 25 50
- Series Openers 50
- Figure 76 51
- Figure 77 51
- Hole for 51
- 3 (number of meters measured) 52
- Tire Revolutions Per Acre 53
- Marker Adjustments 55
- Figure 82 57
- Adjusting Marker Carrier 57
- Shear Bolt 57
- Figure 81 57
- Marker Chain Adjustment 57
- Figure 83 58
- Marker Width Adjustment 58
- Seed-Lok™ Lock Up 60
- Maintenance and Lubrication 67
- Figure 96 71
- Finger Meter 71
- Seed Tube Maintenance 72
- Figure 99 73
- Drive Chains and Idlers 73
- Figure 100 73
- Side Wheels 73
- Figure 101 74
- Opener Disks Contact Point 74
- Figure 102 74
- Disk Spreader 74
- Figure 103 75
- Spreaders and Scrapers 75
- Figure 104 75
- Figure 105 76
- Seed Flap Replacement 76
- Figure 106 76
- Marker Shear Bolt 76
- Lubrication 77
- Seasonally 78
- Seed-Lok™ Firming Wheels 79
- Depth Wheel Scraper 80
- Baffle Kit 80
- DICKEY-john 80
- Monitor 80
- Veris Drive 81
- Weight Bracket Kit 81
- Keeton Seed Firmer 81
- Tractor Hookup 83
- Controller Menu 84
- Console Functions 85
- Calibration 85
- Figure 111 86
- Figure 112 86
- Figure 113 86
- Figure 114 87
- Figure 115 87
- Figure 116 87
- Figure 117 88
- Figure 118 88
- Figure 119 88
- Figure 120 89
- Figure 121 89
- Figure 122 89
- Figure 123 90
- Figure 124 90
- Figure 125 90
- Figure 126 91
- Figure 127 91
- Operations 92
- Veris Drive Sprocket Change 93
- GPS-Based Seeding 96
- 9 pin serial cable 98
- Maintenance 100
- Troubleshooting 101
- 118-928M 102
- 8/14/2006 102
- Troubleshooting Flow Chart 104
- Seed Rate Charts 106
- 2025P, 2020P Bedded, and 108
- Seed Rate Charts for 15” Skip 137
- Row 5/4/5 137
- Sprockets 137
- Appendix 161
- Tire Inflation Chart 162
- Specifications and Capacities 162
- Warranty 165
- Salina, Kansas 67402-5060 USA 166
Related products and manuals for Gardening equipment Great-plains 2025P Operator Manual
(94 pages)
(5 pages)© 2020, manymanuals.com. All rights reserved. | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals