Great-plains 2025P Operator Manual User Manual Page 28
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2025P, 2020P Bedded, and
2010HDP
118-928M
8/14/2006
26
Side Gauge Wheels for 20 and 25 Series
Openers
Refer to Figure 18
The side gauge wheels have two, interrelated adjustments:
• angle of side gauge wheel, and
• distance between side gauge wheel and row unit disk.
Refer to Figure 19
Adjust side-gauge-wheel angle so wheels contact row unit disks
at bottom of wheel at 2” planting depth.
At the same time, keep side gauge wheels close to opener disks
so openers do not plug with soil or trash but far enough out so
disks and wheels turn freely.
• If contact point is between 4 to 8 o’clock but distance to
tire is not correct, then add or remove shims as needed.
DO NOT ADJUST BEARING THAT WILL ADJUST
WHEEL-TO-DISK CONTACT AREA ONLY.
Refer to Figure 20
To adjust Wheel-to-Disk contact area of side gauge wheels:
1. Raise drill slightly to remove weight from side gauge wheels.
2. Loosen hex-head bolt (1). Move wheel and arm out on o-
ring bushing.
3. Loosen pivot bolt (2). Turn hex adjuster (3) so indicator
notch (4) is at 5 o’clock to 7 o’clock. Use this as the starting
point for adjustment.
4. Move wheel arm in so side gauge wheel contacts row unit
disk. Tighten hex-head bolt (1) to clamp arm around bush-
ing and shank.
5. Check wheel-to-disk contact at 2” planting depth. Lift wheel
and arm. When let go, wheel should fall freely.
• If wheel does not contact disk at bottom to area where
blade leaves contact with soil, move hex adjuster until
wheel is angled for proper contact with disk.
• If wheel does not fall freely, loosen hex-head bolt (1) and
slide wheel arm out just until wheel and arm move freely.
Retighten hex-head bolt (1) according to grade:
• 1/2” Gr 5 bolt on 25 series, 75 ft-lbs.
• 7/16” Gr 8 bolt on 20 series, 70 ft-lbs.
• 1/2” Gr 8 bolt on 25 series, 110 ft-lbs.
• 5/8” Gr 8 bolt on 20 series, 150 ft-lbs.
NOTE: Use “Torque Values Chart”, on page 159 for reference.
Side Gauge
Wheel
Side Gauge
Wheel
Opener
Disks
Incorrect Correct
Figure 18
Side Gauge Wheels
22531
Figure 19
Wheel-to-Disk Contact Area
Figure 20
Side Gauge Wheel Adjustment
Starting Point
22525
2
1
3
4
Adjustments
Note: Wheel touches at bottom and gaps open 3/
8” to 5/8” at top.
6. Keep turning hex adjuster and moving wheel arm
until the wheel is adjusted properly. When satis-
fied, tighten pivot bolt (2) to 110 foot-pounds.
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 818-003C 9
- 838-266C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Left-hand 15
- Right-hand 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 23
- Field Operation 24
- Figure 16 25
- Seed Meter 25
- Transporting 26
- Figure 17 27
- Ladder Folded for Transport 27
- Adjustments 28
- 20 Series Openers 29
- 25 Series Openers 31
- HD 10 Series Openers 35
- Figure 42 37
- Double V Press Wheel 37
- Frame Height 39
- Seeding Rate 40
- Figure 49 41
- Figure 50 41
- Figure 1 41
- Figure 51 41
- Figure 55 43
- Changing Seed Meter Wheel for 44
- Spin wheel 45
- Series Openers and 25 Series 47
- Figure 69 48
- Figure 70 48
- Figure 68 48
- Figure 71 49
- Figure 72 49
- HD 10 Series Openers and 25 50
- Series Openers 50
- Figure 76 51
- Figure 77 51
- Hole for 51
- 3 (number of meters measured) 52
- Tire Revolutions Per Acre 53
- Marker Adjustments 55
- Figure 82 57
- Adjusting Marker Carrier 57
- Shear Bolt 57
- Figure 81 57
- Marker Chain Adjustment 57
- Figure 83 58
- Marker Width Adjustment 58
- Seed-Lok™ Lock Up 60
- Maintenance and Lubrication 67
- Figure 96 71
- Finger Meter 71
- Seed Tube Maintenance 72
- Figure 99 73
- Drive Chains and Idlers 73
- Figure 100 73
- Side Wheels 73
- Figure 101 74
- Opener Disks Contact Point 74
- Figure 102 74
- Disk Spreader 74
- Figure 103 75
- Spreaders and Scrapers 75
- Figure 104 75
- Figure 105 76
- Seed Flap Replacement 76
- Figure 106 76
- Marker Shear Bolt 76
- Lubrication 77
- Seasonally 78
- Seed-Lok™ Firming Wheels 79
- Depth Wheel Scraper 80
- Baffle Kit 80
- DICKEY-john 80
- Monitor 80
- Veris Drive 81
- Weight Bracket Kit 81
- Keeton Seed Firmer 81
- Tractor Hookup 83
- Controller Menu 84
- Console Functions 85
- Calibration 85
- Figure 111 86
- Figure 112 86
- Figure 113 86
- Figure 114 87
- Figure 115 87
- Figure 116 87
- Figure 117 88
- Figure 118 88
- Figure 119 88
- Figure 120 89
- Figure 121 89
- Figure 122 89
- Figure 123 90
- Figure 124 90
- Figure 125 90
- Figure 126 91
- Figure 127 91
- Operations 92
- Veris Drive Sprocket Change 93
- GPS-Based Seeding 96
- 9 pin serial cable 98
- Maintenance 100
- Troubleshooting 101
- 118-928M 102
- 8/14/2006 102
- Troubleshooting Flow Chart 104
- Seed Rate Charts 106
- 2025P, 2020P Bedded, and 108
- Seed Rate Charts for 15” Skip 137
- Row 5/4/5 137
- Sprockets 137
- Appendix 161
- Tire Inflation Chart 162
- Specifications and Capacities 162
- Warranty 165
- Salina, Kansas 67402-5060 USA 166
Related products and manuals for Gardening equipment Great-plains 2025P Operator Manual
(94 pages)
(5 pages)© 2020, manymanuals.com. All rights reserved. | 0.717 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals