Great-plains 2025P Operator Manual User Manual Page 33
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8/14/2006
118-928M
31
Adjustments
Refer to Figure 32
Set seeding depth by adjusting handles. To ad-
just, first raise openers slightly, then lift and slide
handles on top of openers. Adjust all handles to
the same setting.
• For shallower seeding, slide handles forward
toward drill.
• For deeper seeding, slide handles back away
from drill.
Press Wheel
Refer to Figure 33
Press wheels are attached to each opener body.
The press wheels close the seed trench and gen-
tly press soil over seed.
An adjustable spring in the press-wheel mecha-
nism creates the down pressure needed to close
the seed trench. The amount of force needed will
vary with field conditions.
To adjust, move adjustment handle.
• For less down pressure, move handle forward
toward drill.
• For more down pressure, move handle back
away from drill.
NOTE: Increased press wheel spring force
may require increased opener down force to
maintain depth.
NOTE: The factory setting on the press wheel
is staggered to achieve optimum residue flow.
Refer to Figure 34
If you want to adjust press wheels from staggered
to even, remove 5/8 inch bolt (1), lock washer (2)
and nut (3). Reinstall spacer (4), press wheel (5)
and hardware to the other hole location.
If you want to move the press wheels apart, re-
move spacer (6) from beneath the bolt head (1)
and place it next to spacer (4).
Figure 32
25 Series Opener Depth
21949
Handle
More down
pressure
Less down
pressure
21949
Figure 34
Press Wheel Stagger
22527
Hole
locations
Figure 33
Press Wheel Adjustment
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 818-003C 9
- 838-266C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Left-hand 15
- Right-hand 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 23
- Field Operation 24
- Figure 16 25
- Seed Meter 25
- Transporting 26
- Figure 17 27
- Ladder Folded for Transport 27
- Adjustments 28
- 20 Series Openers 29
- 25 Series Openers 31
- HD 10 Series Openers 35
- Figure 42 37
- Double V Press Wheel 37
- Frame Height 39
- Seeding Rate 40
- Figure 49 41
- Figure 50 41
- Figure 1 41
- Figure 51 41
- Figure 55 43
- Changing Seed Meter Wheel for 44
- Spin wheel 45
- Series Openers and 25 Series 47
- Figure 69 48
- Figure 70 48
- Figure 68 48
- Figure 71 49
- Figure 72 49
- HD 10 Series Openers and 25 50
- Series Openers 50
- Figure 76 51
- Figure 77 51
- Hole for 51
- 3 (number of meters measured) 52
- Tire Revolutions Per Acre 53
- Marker Adjustments 55
- Figure 82 57
- Adjusting Marker Carrier 57
- Shear Bolt 57
- Figure 81 57
- Marker Chain Adjustment 57
- Figure 83 58
- Marker Width Adjustment 58
- Seed-Lok™ Lock Up 60
- Maintenance and Lubrication 67
- Figure 96 71
- Finger Meter 71
- Seed Tube Maintenance 72
- Figure 99 73
- Drive Chains and Idlers 73
- Figure 100 73
- Side Wheels 73
- Figure 101 74
- Opener Disks Contact Point 74
- Figure 102 74
- Disk Spreader 74
- Figure 103 75
- Spreaders and Scrapers 75
- Figure 104 75
- Figure 105 76
- Seed Flap Replacement 76
- Figure 106 76
- Marker Shear Bolt 76
- Lubrication 77
- Seasonally 78
- Seed-Lok™ Firming Wheels 79
- Depth Wheel Scraper 80
- Baffle Kit 80
- DICKEY-john 80
- Monitor 80
- Veris Drive 81
- Weight Bracket Kit 81
- Keeton Seed Firmer 81
- Tractor Hookup 83
- Controller Menu 84
- Console Functions 85
- Calibration 85
- Figure 111 86
- Figure 112 86
- Figure 113 86
- Figure 114 87
- Figure 115 87
- Figure 116 87
- Figure 117 88
- Figure 118 88
- Figure 119 88
- Figure 120 89
- Figure 121 89
- Figure 122 89
- Figure 123 90
- Figure 124 90
- Figure 125 90
- Figure 126 91
- Figure 127 91
- Operations 92
- Veris Drive Sprocket Change 93
- GPS-Based Seeding 96
- 9 pin serial cable 98
- Maintenance 100
- Troubleshooting 101
- 118-928M 102
- 8/14/2006 102
- Troubleshooting Flow Chart 104
- Seed Rate Charts 106
- 2025P, 2020P Bedded, and 108
- Seed Rate Charts for 15” Skip 137
- Row 5/4/5 137
- Sprockets 137
- Appendix 161
- Tire Inflation Chart 162
- Specifications and Capacities 162
- Warranty 165
- Salina, Kansas 67402-5060 USA 166
Related products and manuals for Gardening equipment Great-plains 2025P Operator Manual
(94 pages)
(5 pages)© 2020, manymanuals.com. All rights reserved. | 0.609 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals