Great-plains NP4000B Operator Manual User Manual Page 146
- Page / 200
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
142 2013+ NP4000/A/B Table of Contents Index Great Plains Manufacturing, Inc.
417-199M Table of Contents Index 2014-05-14
Ground Drive Wheel Hub (Option)
1 zerk at each bearing casting;
4 total
Type of Lubrication: Grease
Quantity: Until grease emerges
Fertilizer Drive: Chains (Option)
3 chains
Type of Lubrication: Chain Lube
Quantity = Coat thoroughly
Note: Lubricate chains any time there is a chance of
moisture, and when being stored at the end of the
planting season.
Caster Wheel Bearings
2 races total
Type of Lubrication: Grease
Quantity = until resistance is felt
10
31079
As Required
31079
Seasonal
34930
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Look for Safety Symbol 6
- Be Aware of Signal Words 6
- Prepare for Emergencies 6
- Use Safety Chains 8
- Avoid High Pressure Fluids 8
- Minimize Radiation Exposure 8
- Keep Riders Off Machinery 8
- Use Safety Lights and Devices 9
- Tires Not a Step 9
- Transport Machinery Safely 10
- Shutdown and Storage 11
- Handle Chemicals Properly 11
- Tire Safety 12
- Practice Safe Maintenance 12
- Safety At All Times 12
- Safety Decals 13
- 818-323C 15
- 818-590C 15
- Danger: Hitch Crush 15
- 848-801C 20
- 848-539C 21
- Introduction 22
- Using This Manual 23
- Owner Assistance 24
- Application Overview 25
- A35 A39 A40 26
- Figure 5 32
- Figure 6 33
- Nutri-Pro 37
- Rear Hitch (Option) 37
- Figure 7 38
- Trailing Nurse Tank Hitch 38
- Preparation and Setup 39
- NP4000A: Get Expert Advice 40
- Pre-Application Setup 40
- 2-Point Hitching 41
- Hydraulic Hose Hookup 45
- Date Code 46
- Motor Model (206N) 46
- Inlet Port 46
- Outlet Port 46
- Leveling Applicator 47
- Wash Water (NP4000A) 51
- Sealer Setup (NP4000A) 51
- Operating Instructions 52
- Fold/Lift Circuit 53
- FOLD / FIELD Switch 53
- Applicator Locks 54
- Raising/Lowering Applicator 55
- Unfolding and Folding 60
- Transport 63
- Final Applicator Setup 64
- Operations 65
- : Pass Planning 70
- Liquid Operations 78
- Liq: Hydraulic Drive Start-Up 81
- Liq: Pauses and Turns 81
- Suspending Application 83
- Liq: Stopping Application 83
- Field Set-Up Checklists 84
- Checklist (Cart Hitched) 85
- Plumbing Checklist Page 85
- Field Operation Checklists 86
- Short-Term Parking 88
- Long-Term Storage 88
- Adjustments 89
- Row Adjustments 90
- Handle Slot Down-Pressure 91
- Tool Bar Height Adjustment 95
- Weight Transfer Adjustment 96
- NUTRI-PRO 97
- Caster Angle Adjustment 98
- Fertilizer Rates 99
- NP4000-1630 Fertilizer Rate 100
- NP4000B-1238 Fertilizer Rate 102
- NP4000B-1240 Fertilizer Rate 103
- Strainer Adjustment 106
- Flow-Based Adjustment 109
- Dead-Head Adjustment 109
- Troubleshooting 110
- FOLD / FIELD Troubleshooting 111
- Maintenance and Lubrication 119
- Avoid Trapped Anhydrous 120
- Avoid Ball Traps 121
- System Discharge 122
- Clearing Plugged Tines 124
- Valve Replacement 127
- Replacement Log 128
- Refrigerant Line 129
- Row Delivery Tubing 130
- Row Vapor Tubing 130
- Metering System Maintenance 131
- Material Clean-Out (Liquid) 132
- Pump Maintenance and Repair 134
- Coulter Disc Replacement 134
- Coulter Spring Setting 135
- Hydraulic Maintenance 136
- Bleeding Fold Hydraulics 137
- Wing Leveling 140
- Rear Eyebolt Adjustment 140
- Caster Brake Adjustment 141
- Chain Maintenance (Option) 142
- Inner Wing Pivots 143
- Outer Wing Pivots 143
- Caster Pivots 143
- Lift- Assist Parallel Arms 144
- Fertilizer Pump Crankshaft 145
- Tire Pressures 145
- As Required 146
- Seasonal 146
- Sub-frame and Tank Selection 148
- Category II Hitch Pin Kit 148
- Rear Hitches 149
- Nurse Tank Light Harness 150
- Row Cleaners 150
- Terra-Tine™ Row Cleaners 150
- Coulters, Blades and Tines 151
- Vantage I Attachment Kits 152
- Coulter Nozzles 152
- Speed Sensor Cable 153
- Speed Sensor 153
- Manifolds and Accessories 154
- Liquid Fertilizer Pumps 155
- Side Dress Extensions 156
- Weight Kit 157
- Specifications and Capacities 158
- Dimensions 161
- Torque Values Chart 163
- Tire Inflation Chart 163
- Plumbing Diagrams 164
- Chain Routing (Option) 172
- Controller System Diagrams 173
- GP: 823-422C 174
- Hydraulic Pump Controller 175
- Hydraulic Diagrams 176
- Pump Hydraulics (Option) 179
- Component Replacement Dates 180
- Post-Delivery Checklist 180
- Lift-Assist Valve Setup 181
- Hydraulic Pump Setup 182
- Console Installation 183
- Side Dress Installation 184
- Refer to Figure 103 186
- 803-027C NUT HEX 3/4-10 PLT 188
- 990-259R EVA TUBING 3/8 ID 189
- Weight Kit Installation 191
- Warranty 192
- Table of Contents Index 199
- Salina, Kansas 67402-5060 USA 200
Related products and manuals for Gardening equipment Great-plains NP4000B Operator Manual
(48 pages)
(50 pages)
(128 pages)© 2020, manymanuals.com. All rights reserved. | 1.376 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals