Great-plains YP825AR Operator Manual User Manual Page 76
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
72 YP825AR Table of Contents Index Great Plains Manufacturing, Inc.
401-923M Table of Contents Index 2014-06-17
Side Gauge Wheel Adjustment
Refer to Figure 84 and Figure 85
Disc-to-wheel angle and clearance ideally has the wheel
just touching the disk when the wheel is raised to
planting depth (is up against the stop set by the “T”
handle. The goal is to have both disks and wheels turn
freely, but keep soil and trash from getting between them.
These two adjustments interact with each other.
Changing one requires at least checking the other.
In addition to changing the disk angle due to changing
depth or new field conditions, these two settings may
need attention over time as the disk and wheels wear
from normal use. This adjustment will also need to be
made if any opener components are replaced.
For 2 inch (5.1 cm) planting depth, adjust side gauge
wheel angle so wheels contact row unit disks at the
bottom of wheel. Check with row units in soil so wheels
are held up.
At the same time, keep side gauge wheels close to
opener disks so openers do not plug with soil or trash.
Note: Wheels should be out far enough so disks and
wheels turn freely.
Refer to Figure 87 on page 73
To adjust side gauge wheels:
1. Raise the planter and install lift cylinder locks.
2. Loosen hex-head bolt . Move wheel and arm out
on O-ring bushing.
3. Loosen pivot bolt Turn hex adjuster so indicator
notch is at 5 o’clock to 7 o’clock.
Note: Use this as the starting point for adjustment.
4. Move wheel arm in so side gauge wheel contacts
row unit disk. Tighten hex-head bolt to clamp arm
around bushing and shank.
Refer to Figure 86
5. Check wheel-to-disk contact at 2 inches (5.2 cm)
planting depth. Lift wheel 2 inches, check contact
and release. When let go, wheel should fall freely.
• If wheel does not contact disk at bottom to area where
blade leaves contact with soil, move hex adjuster until
wheel is angled for proper contact with disk.
Figure 84
Disk/Gauge Wheel Alignment
Side Gauge
Wheel
Side Gauge
Wheel
Incorrect
Correct
Opener
Disks
Figure 85
Opener-Gauge Wheel Contact
22531
Contact Within this Area
Figure 86
Checking Wheel/Disc Contact
26129
1
2 3
4
1
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Wear Protective Equipment 6
- Avoid High Pressure Fluids 6
- Use A Safety Chain 7
- Keep Riders Off Machinery 7
- Use Safety Lights and Devices 7
- Transport Machinery Safely 7
- Shutdown and Storage 8
- Tire Safety 8
- Handle Chemicals Properly 8
- Practice Safe Maintenance 9
- Safety At All Times 9
- Safety Decals 10
- READ BEFORE USING TANK 11
- EXCESSIVE SPEED HAZARD 12
- 848-801C 14
- Introduction 15
- Using This Manual 16
- Owner Assistance 16
- Preparation and Setup 17
- Hitching Tractor to Planter 18
- Hydraulic Hose Hookup 20
- Air Source Setup (Option) 21
- Leveling Planter 22
- Monitor Setup 24
- Marker Setup (Option) 24
- Lock Up Fertilizer Drive 25
- Operating Instructions 26
- Transport 27
- Transport Steps 28
- Color Function 29
- CLOSED OPEN 30
- Unfolding/Folding the Planter 31
- 34702-04 34
- Field Lift/Lower 39
- Marker Operations 40
- Loading Materials 41
- Loading Seed, continued 42
- Air System Operation 49
- 848-020C 52
- Meter Operation 53
- Field Set-Up Checklists 54
- Field Operation 55
- Short-Term Parking 56
- Long-Term Storage 56
- Adjustments 57
- Setting Material Rates 58
- Marker Adjustments (Option) 59
- Fan and Gauge Adjustment 60
- Single-Row Augers 64
- Row Implement Adjustments 66
- Row Unit Down Pressure 70
- UMC Coulter Adjustments 73
- Side Gauge Wheel Adjustment 76
- Row Unit Shut-Off 82
- Seed Firmer Adjustments 84
- Troubleshooting 87
- Seed Pool Troubleshooting 88
- Problem Cause Solution 89
- Population Too Low 90
- Population Too High 91
- Population Related 93
- General Troubleshooting 94
- Maintenance and Lubrication 99
- Material Clean-Out 100
- Liquid Fertilizer Clean-Out 102
- Dry Fertilizer Clean-Out 103
- Hydraulic Maintenance 109
- As Required 112
- 25474 25475 116
- Seasonal 118
- Seed Lubricants 120
- Seed Monitor 121
- Seed Meter Drive 121
- PTO Pump 122
- Speed Radar 124
- Liquid Fertilizer System 124
- Dry Fertilizer System 125
- Dual Sequenced Markers 126
- Frame-Mounted Row Accessories 126
- Terra-Tine™ 127
- Row-Mounted Accessories 128
- Unit-Mounted Disk Coulters 129
- Seed Meter Disks 129
- Inside Disk Scrapers 130
- Gauge Wheel Scrapers 130
- Seed Firmers 130
- Row Unit Press Wheels 131
- Lock-Up Pins 131
- Seed Lubricant 131
- Clean-Out Container 132
- Seed Tube Brush 132
- Specifications and Capacities 134
- 70 and 75 cm Models 135
- Dimensions 136
- Field Dimensions 137
- Torque Values Chart 138
- Tire Inflation Chart 138
- Plumbing Diagrams 139
- Hydraulic Diagrams 140
- Chain Routing 149
- Twin Row Single Row 151
- 15T, 47T 152
- 25AP: Meter Drive (Mid type) 153
- 25AP: Meter Drive (Rear type) 153
- Appendix C - Initial Setup 154
- Marker Extension 155
- 122-278S Scraper Installation 158
- NOZZLE SHUT OFF CAP W/ GASKET 159
- Table of Contents Index 165
- Salina, Kansas 67402-5060 USA 166
Related products and manuals for Gardening equipment Great-plains YP825AR Operator Manual
(8 pages)
(50 pages)
(128 pages)© 2020, manymanuals.com. All rights reserved. | 0.216 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals