Great-plains 2025P Operator Manual User Manual Page 19
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8/14/2006
118-928M
17
Preparation and Setup
Leveling the Drill
20 Series Opener Single Gauge Wheel
Refer to Figure 4
Initially adjust drill so bottom of opener tube runs
24 inches above ground when drill is lowered in
the field.
Refer to Figure 5
To adjust:
1. Make sure block mount of the spring linkage
(2) is in the lower mount hole for planting in
bedded irrigation. The upper hole is for non-
bedded ground.
2. Set spring linkage length. Turn spring linkage
to shorten or lengthen as necessary. Initially
set length to 6 1/8 inches between pin centers
to achieve the 24-inch dimension mentioned
above. When adjusting the linkage length, re-
member:
• Lengthening linkage raises drill.
• Shortening linkage lowers drill.
3. Level drill with top three-point link.
Refer to Figure 6
NOTE: When drill is level, parallel links will be
running slightly uphill towards the front.
The 1-inch dimension shown is a general dimen-
sion that will vary with planting conditions.
IMPORTANT: Make sure the opener mount is
running higher than the opener body. This will
ensure an ample reserve for opener upfloat in
case the opener strikes a rock or other object.
Figure 4
Initial Operating Height
18280
Figure 5
Spring Linkage
21685
Figure 6
Leveling the Drill
18288
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 818-003C 9
- 838-266C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Left-hand 15
- Right-hand 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 23
- Field Operation 24
- Figure 16 25
- Seed Meter 25
- Transporting 26
- Figure 17 27
- Ladder Folded for Transport 27
- Adjustments 28
- 20 Series Openers 29
- 25 Series Openers 31
- HD 10 Series Openers 35
- Figure 42 37
- Double V Press Wheel 37
- Frame Height 39
- Seeding Rate 40
- Figure 49 41
- Figure 50 41
- Figure 1 41
- Figure 51 41
- Figure 55 43
- Changing Seed Meter Wheel for 44
- Spin wheel 45
- Series Openers and 25 Series 47
- Figure 69 48
- Figure 70 48
- Figure 68 48
- Figure 71 49
- Figure 72 49
- HD 10 Series Openers and 25 50
- Series Openers 50
- Figure 76 51
- Figure 77 51
- Hole for 51
- 3 (number of meters measured) 52
- Tire Revolutions Per Acre 53
- Marker Adjustments 55
- Figure 82 57
- Adjusting Marker Carrier 57
- Shear Bolt 57
- Figure 81 57
- Marker Chain Adjustment 57
- Figure 83 58
- Marker Width Adjustment 58
- Seed-Lok™ Lock Up 60
- Maintenance and Lubrication 67
- Figure 96 71
- Finger Meter 71
- Seed Tube Maintenance 72
- Figure 99 73
- Drive Chains and Idlers 73
- Figure 100 73
- Side Wheels 73
- Figure 101 74
- Opener Disks Contact Point 74
- Figure 102 74
- Disk Spreader 74
- Figure 103 75
- Spreaders and Scrapers 75
- Figure 104 75
- Figure 105 76
- Seed Flap Replacement 76
- Figure 106 76
- Marker Shear Bolt 76
- Lubrication 77
- Seasonally 78
- Seed-Lok™ Firming Wheels 79
- Depth Wheel Scraper 80
- Baffle Kit 80
- DICKEY-john 80
- Monitor 80
- Veris Drive 81
- Weight Bracket Kit 81
- Keeton Seed Firmer 81
- Tractor Hookup 83
- Controller Menu 84
- Console Functions 85
- Calibration 85
- Figure 111 86
- Figure 112 86
- Figure 113 86
- Figure 114 87
- Figure 115 87
- Figure 116 87
- Figure 117 88
- Figure 118 88
- Figure 119 88
- Figure 120 89
- Figure 121 89
- Figure 122 89
- Figure 123 90
- Figure 124 90
- Figure 125 90
- Figure 126 91
- Figure 127 91
- Operations 92
- Veris Drive Sprocket Change 93
- GPS-Based Seeding 96
- 9 pin serial cable 98
- Maintenance 100
- Troubleshooting 101
- 118-928M 102
- 8/14/2006 102
- Troubleshooting Flow Chart 104
- Seed Rate Charts 106
- 2025P, 2020P Bedded, and 108
- Seed Rate Charts for 15” Skip 137
- Row 5/4/5 137
- Sprockets 137
- Appendix 161
- Tire Inflation Chart 162
- Specifications and Capacities 162
- Warranty 165
- Salina, Kansas 67402-5060 USA 166
Related products and manuals for Gardening equipment Great-plains 2025P Operator Manual
(94 pages)
(5 pages)© 2020, manymanuals.com. All rights reserved. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals