Great-plains 2025P Operator Manual User Manual Page 92
- Page / 166
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2025P, 2020P Bedded, and
2010HDP
118-928M
8/14/2006
90
Operations
Before going to the field:
1. Once calibration procedure above has been
followed, Console will store calibration and rate
information until new information has been en-
tered.
Refer to Figure 128
2. Turn on Console by pressing On/VR key.
Pressing On/VR key twice will put unit in VR
(Variable Rate) mode. Leave Console in man-
ual mode.
NOTE: For units with P/N 21567 skip step 3.
3. To double-check calibration before planting,
follow same procedure as for mechanical
ground drives as outlined in Great Plains Pre-
cision Seeding System Operator’s Manual,
with these differences:
• Volumetric: use extreme caution when per-
forming this calibration to prevent injury due to
drive entanglement. Also, turn drive gauge
wheel with a consistent speed of at least 30
rpm for maximum calibration accuracy.
• Singulated: Rather than calibrating from a
standing start, measure the distance as listed
in the GP manual, and set two flags. Start driv-
ing far enough in advance of the first flag that
your unit is operating at field speed (min. 3
mph) during the calibration distance.
In Field:
Refer to Figure 129
1. Turn on Controller Console by pressing On/VR
key. Green light above On/VR key will illumi-
nate when power is on. Pressing On/VR key
twice will put the unit in VR mode. VR will ap-
pear on screen along with Rate that is being
sent from the computer. Press On/VR key
again to toggle back to manual mode. (Mode
and rate changes take effect with the release of
the key.)
2. To change rates manually whether in manual
or in VR mode, simply touch Up/Down arrow
keys. This will change Controller to the rate you
select manually. To return to VR, simply touch
On/VR key to toggle back to VR mode.
3. Engage hydraulic flow by pushing FORWARD
on the tractor remote hydraulic lever. The re-
mote lever must be LOCKED OPEN in this po-
sition to provide constant flow to the drive
motor.
• John Deere tractors with Sound-Gard ®
body: Use lever lock clip to lock lever forward.
See your tractor dealer for lock purchase and in-
stallation.
• John Deere 7000 Series tractors: Rotate valve
detent selector to motor position to lock lever in
forward position.
• John Deere 8000 Series tractors: Set timer to
continuous. Push lever forward until detent
clicks.
• Case-IH Magnum tractors: Lock lever forward
in detent position. You may need to turn up de-
tent pressure to maximum setting. Do not tie hy-
draulic lever past detent position with a strap.
See your tractor dealer for details.
• Other tractors: Lock lever forward in detent po-
sition. You may need to turn detent pressure to
maximum or use a mechanical detent holder to
hold lever forward. See your tractor dealer for
proper means of providing constant flow.
4. Press Engage key to activate drive. Green light
above Engage key will illuminate.
NOTE: If you do not move within 10 seconds, the
automatic disengagement feature will disengage
the drive. To begin planting again, you must
press Engage key.
Figure 128
Figure 129
22710
22734
- Operator’s Manual 1
- Table of Contents 2
- Important Safety Information 3
- Keep Riders Off Machinery 4
- Shutdown and Storage 4
- Use Safety Lights and Devices 4
- Transport Machinery Safely 5
- Avoid High Pressure Fluids 5
- Practice Safe Maintenance 6
- Prepare for Emergencies 6
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Use A Safety Chain 7
- Tire Safety 7
- Safety At All Times 8
- Safety Decals 9
- 818-003C 9
- 838-266C 9
- 818-339C 10
- 838-265C 10
- 838-267C 10
- 818-587C 11
- 818-590C 11
- 838-102C 11
- 818-855C 12
- 818-229C 12
- 818-398C 12
- 818-682C 13
- 818-337C 13
- 818-752C 13
- Introduction 14
- Left-hand 15
- Right-hand 15
- Owner Assistance 16
- Preparation and Setup 17
- Figure 3 18
- Hydraulic Hose Label 18
- Leveling the Drill 19
- Operating Instructions 23
- Field Operation 24
- Figure 16 25
- Seed Meter 25
- Transporting 26
- Figure 17 27
- Ladder Folded for Transport 27
- Adjustments 28
- 20 Series Openers 29
- 25 Series Openers 31
- HD 10 Series Openers 35
- Figure 42 37
- Double V Press Wheel 37
- Frame Height 39
- Seeding Rate 40
- Figure 49 41
- Figure 50 41
- Figure 1 41
- Figure 51 41
- Figure 55 43
- Changing Seed Meter Wheel for 44
- Spin wheel 45
- Series Openers and 25 Series 47
- Figure 69 48
- Figure 70 48
- Figure 68 48
- Figure 71 49
- Figure 72 49
- HD 10 Series Openers and 25 50
- Series Openers 50
- Figure 76 51
- Figure 77 51
- Hole for 51
- 3 (number of meters measured) 52
- Tire Revolutions Per Acre 53
- Marker Adjustments 55
- Figure 82 57
- Adjusting Marker Carrier 57
- Shear Bolt 57
- Figure 81 57
- Marker Chain Adjustment 57
- Figure 83 58
- Marker Width Adjustment 58
- Seed-Lok™ Lock Up 60
- Maintenance and Lubrication 67
- Figure 96 71
- Finger Meter 71
- Seed Tube Maintenance 72
- Figure 99 73
- Drive Chains and Idlers 73
- Figure 100 73
- Side Wheels 73
- Figure 101 74
- Opener Disks Contact Point 74
- Figure 102 74
- Disk Spreader 74
- Figure 103 75
- Spreaders and Scrapers 75
- Figure 104 75
- Figure 105 76
- Seed Flap Replacement 76
- Figure 106 76
- Marker Shear Bolt 76
- Lubrication 77
- Seasonally 78
- Seed-Lok™ Firming Wheels 79
- Depth Wheel Scraper 80
- Baffle Kit 80
- DICKEY-john 80
- Monitor 80
- Veris Drive 81
- Weight Bracket Kit 81
- Keeton Seed Firmer 81
- Tractor Hookup 83
- Controller Menu 84
- Console Functions 85
- Calibration 85
- Figure 111 86
- Figure 112 86
- Figure 113 86
- Figure 114 87
- Figure 115 87
- Figure 116 87
- Figure 117 88
- Figure 118 88
- Figure 119 88
- Figure 120 89
- Figure 121 89
- Figure 122 89
- Figure 123 90
- Figure 124 90
- Figure 125 90
- Figure 126 91
- Figure 127 91
- Operations 92
- Veris Drive Sprocket Change 93
- GPS-Based Seeding 96
- 9 pin serial cable 98
- Maintenance 100
- Troubleshooting 101
- 118-928M 102
- 8/14/2006 102
- Troubleshooting Flow Chart 104
- Seed Rate Charts 106
- 2025P, 2020P Bedded, and 108
- Seed Rate Charts for 15” Skip 137
- Row 5/4/5 137
- Sprockets 137
- Appendix 161
- Tire Inflation Chart 162
- Specifications and Capacities 162
- Warranty 165
- Salina, Kansas 67402-5060 USA 166
Related products and manuals for Gardening equipment Great-plains 2025P Operator Manual
(94 pages)
(5 pages)© 2020, manymanuals.com. All rights reserved. | 1.911 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals