Great-plains ADC2350BE Operator Manual User Manual Page 70
- Page / 108
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
66 ADC2350/E and ADC2350B/BE Table of Contents Index Great Plains Manufacturing, Inc.
167-085M Table of Contents Index 2012-08-01
Changing Meter Flutes
To order high rate flute shafts, see “Alternate Flute
Sets” on page 85. To install a set of these shafts (or
re-install the standard shafts), start with the front meter,
as the task is a bit easier there. Save all parts for
immediate or future re-use.
Hopper must be empty for this procedure. see
“Unloading the Cart” on page 47.
Refer to Figure 74
1. On the right end of the meter box, remove and save
the lynch pins from the final range gears , and
then remove and save the gears.
Note which size gear was on the agitator output and
flute input shaft.
Refer to Figure 75
2. Remove and save the outer ring of six (6)
self-tapping hex head bolts , that secure the outer
flange to the meter box.
Note: Do not remove the six bolts that secure the
bearing flangette to the outer flange. The shaft to
be installed includes its own flange.
Refer to Figure 76
(Shown with meter box off and various components removed
for clarity. It is not necessary to dismount or further
disassemble meters to swap flute shafts).
3. From the right end of the meter box, carefully
withdraw the current flute shaft . It is likely that the
flange has a bead of silicone gasket. You may need
to carefully pry the flange loose from the box.
Note: For the rear meter box
It will not be possible to withdraw the shaft straight
out, as it would strike the tire. When the right end of
the shaft is close to the tire, angle the shaft forward
to clear the tire.
4. Store the old shaft in the carton in which the new
shaft was supplied. Mark the carton with the number
of active hoses (towers) and the number of stars
(factory standard is 2). This will reduce the risk of
mistaking the carton/contents in the future.
5. Apply a bead of silicone sealant to the inside face of
the outer flange, just inside the bolt hole pattern.
6. Carefully insert the new shaft in the meter box.
Figure 74
Remove Gears
26337
2
1
1
2
1 2
Figure 75
Remove Flange Bolts
26338
2
1
1
2
Figure 76
Exchange Flute Shafts
26335
1
2
1
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Avoid High Pressure Fluids 6
- Use A Safety Chain 6
- Keep Riders Off Machinery 6
- Use Safety Lights and Devices 6
- Check for Overhead Lines 7
- Transport Machinery Safely 7
- Wear Protective Equipment 7
- Handle Chemicals Properly 8
- Confined Space 8
- Shutdown and Storage 8
- Practice Safe Maintenance 9
- Tire Safety 9
- Safety At All Times 9
- Safety Decals 10
- 838-266C 11
- Red Reflectors 11
- 838-265C 11
- Amber Reflectors 11
- 838-267C 12
- Daytime Reflectors 12
- 818-557C 12
- Danger: Cannot Read English 12
- EXCESSIVE SPEED HAZARD 14
- 818-339C 15
- 818-622C 15
- Introduction 19
- Using This Manual 20
- Owner Assistance 21
- Preparation and Setup 22
- Cart Drive System 23
- Hitching 24
- Color Hydraulic Function 28
- 817-348c 29
- Set Up the Implement 32
- Row Setup Data 33
- Operating Instructions 35
- Walkboard Ladders 36
- Hopper Lids 37
- Strainer 38
- Meter Doors 39
- Meter Hand Crank 40
- Drive Chain Lockout 41
- Auger Operations 42
- Transport 45
- Monitor Material Configuration 47
- Loading Material 48
- Cart Diverter Valve 49
- Unloading the Cart 51
- Unloading Front Hopper 53
- Unloading Rear Hopper 54
- Unloading Closeout 56
- Field Operations 57
- Final Field Checklist 58
- Planting Sequence 58
- Planting 58
- Adjustments 60
- Hoppers for This Material 62
- Single Dual 62
- Meter Rate Adjustment 64
- FINAL DRIVE 65
- DRIVING DRIVEN 65
- Changing Meter Flutes 70
- Fan Speed Adjustment 72
- 3N-4010HDA Lift Switch 73
- Clutch Lock-Up 74
- Troubleshooting 75
- Excessive seed 77
- Problem Cause Solution 77
- Maintenance and Lubrication 78
- Chain Slack 79
- Problem Clean-Outs 81
- Hopper Entry 82
- As Required 85
- Seasonal 87
- Blockage Detector 88
- 10 inch Seed Monitor Console 88
- Alternate Flute Sets 89
- ADC2350/E Hitches 90
- Variable Rate Control 90
- Appendix 91
- Torque Values Chart 92
- Chain Routing 93
- Hydraulic Diagrams 94
- ADC2350/E Hydraulic Circuits 95
- Warranty 102
- Table of Contents Index 107
- Salina, Kansas 67402-5060 USA 108
Related products and manuals for Gardening equipment Great-plains ADC2350BE Operator Manual
(54 pages)
(49 pages)© 2020, manymanuals.com. All rights reserved. | 0.202 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals