Great-plains ADC2350BE Operator Manual User Manual Page 73
- Page / 108
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Great Plains Manufacturing, Inc. Table of Contents Index Adjustments 69
2012-08-01 Table of Contents Index 167-085M
Implement Lift Switch Adjustment
Refer to Figure 79, which depicts a model NTA3510 drill.
An implement lift switch on the drill turns seed metering
off when the implement is raised. To adjust the height at
which seed metering is turned off, first locate the lift
switch on the implement. See table below.
Do not place any part of body under implement while making
adjustments.
CTA4000 and CTA4000HD Lift Switch
Raise openers completely. Lock them up by moving the
FIELD/TRANS valve handle to TRANS. Loosen switch
mount bolts and slide switch up or down until the flexible
switch toggle makes contact with the top of the opener
sub-frame arm (toggle is bent up). Adjust the switch until
the toggle activates the switching.
NTA3010 and NTA3510 Lift Switch
Lower the implement until at a height where seeding
should start (usually just above ground). Turn off the
tractor and remove the key. Securely support implement
frame at this height with jack stands or blocks. Loosen
switch bracket bolts and slide switch up or down until the
flexible switch toggle is just past the point at which the
switch is activated (flexible switch toggle not contacting
anything).
3N-4010HDA Lift Switch
Lower the implement until at a height where seeding
seeding should stop (usually just above ground). Turn off
the tractor and remove the key. Securely support
implement frame at this height with jack stands or blocks.
Loosen switch bracket bolts and slide switch up or down
until the flexible switch toggle makes contact with the
bottom of the implement rear parallel lift arm. Adjust the
switch until the toggle activates the switching.
Drill Model Lift Switch Location
CTA4000 Lift arm, mainframe front
CTA4000HD Lift arm, mainframe front
NTA3010 Right rear parallel lift arms
NTA3510 Right rear parallel lift arms
3N-4010HDA Right rear parallel lift arms
Note: The implement lift switch has three wires (black,
red and green). In order for the switch to work
properly, the correct two leads must be connected
to the lift switch extension cable.
The extension cable black lead always connects to
the switch black wire.
The extension cable red lead must connect to the
switch wire color indicated in the table below, for
your implement.
Figure 79
NTA Height Switch
26366
Drill
Model
Lift Switch
Extension Cable
Red Wire to...
Switch State
Drill Raised
CTA4000 Switch Wire: Red Closed
CTA4000HD Switch Wire: Red Closed
NTA3010 Switch Wire: Green Open
NTA3510 Switch Wire: Green Open
3N-4010HDA Switch Wire: Red Closed
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Avoid High Pressure Fluids 6
- Use A Safety Chain 6
- Keep Riders Off Machinery 6
- Use Safety Lights and Devices 6
- Check for Overhead Lines 7
- Transport Machinery Safely 7
- Wear Protective Equipment 7
- Handle Chemicals Properly 8
- Confined Space 8
- Shutdown and Storage 8
- Practice Safe Maintenance 9
- Tire Safety 9
- Safety At All Times 9
- Safety Decals 10
- 838-266C 11
- Red Reflectors 11
- 838-265C 11
- Amber Reflectors 11
- 838-267C 12
- Daytime Reflectors 12
- 818-557C 12
- Danger: Cannot Read English 12
- EXCESSIVE SPEED HAZARD 14
- 818-339C 15
- 818-622C 15
- Introduction 19
- Using This Manual 20
- Owner Assistance 21
- Preparation and Setup 22
- Cart Drive System 23
- Hitching 24
- Color Hydraulic Function 28
- 817-348c 29
- Set Up the Implement 32
- Row Setup Data 33
- Operating Instructions 35
- Walkboard Ladders 36
- Hopper Lids 37
- Strainer 38
- Meter Doors 39
- Meter Hand Crank 40
- Drive Chain Lockout 41
- Auger Operations 42
- Transport 45
- Monitor Material Configuration 47
- Loading Material 48
- Cart Diverter Valve 49
- Unloading the Cart 51
- Unloading Front Hopper 53
- Unloading Rear Hopper 54
- Unloading Closeout 56
- Field Operations 57
- Final Field Checklist 58
- Planting Sequence 58
- Planting 58
- Adjustments 60
- Hoppers for This Material 62
- Single Dual 62
- Meter Rate Adjustment 64
- FINAL DRIVE 65
- DRIVING DRIVEN 65
- Changing Meter Flutes 70
- Fan Speed Adjustment 72
- 3N-4010HDA Lift Switch 73
- Clutch Lock-Up 74
- Troubleshooting 75
- Excessive seed 77
- Problem Cause Solution 77
- Maintenance and Lubrication 78
- Chain Slack 79
- Problem Clean-Outs 81
- Hopper Entry 82
- As Required 85
- Seasonal 87
- Blockage Detector 88
- 10 inch Seed Monitor Console 88
- Alternate Flute Sets 89
- ADC2350/E Hitches 90
- Variable Rate Control 90
- Appendix 91
- Torque Values Chart 92
- Chain Routing 93
- Hydraulic Diagrams 94
- ADC2350/E Hydraulic Circuits 95
- Warranty 102
- Table of Contents Index 107
- Salina, Kansas 67402-5060 USA 108
Related products and manuals for Gardening equipment Great-plains ADC2350BE Operator Manual
(54 pages)
(49 pages)© 2020, manymanuals.com. All rights reserved. | 1.702 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals