Great-plains TSF1290 Operator Manual User Manual Page 43
- Page / 96
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Great Plains Manufacturing, Inc. Operations 39
05/10/2012 500-641M
Valves operate by moving their handles to point at the
function on the decal, or toward the pipe desired on an
otherwise unmarked selector valve. Shut-off valves are
open when the handle is parallel to the piping, and
closed when the handle is perpendicular.
Fluid is drawn from the main tank via the sump
and passes through the pump. The illustration shows
an Ace hydraulic pump, but your pump may be PTO or a
non-standard installation.
From the pump, fluid passes through the solution Whirlfil-
ter® , which filters out or grinds up all undissolved
chemical and solid particles. The fluid then passes
through both the flow meter and the bypass control
butterfly valve .
The bypass control butterfly valve controls how much
fluid goes to the boom. This is regulated by the Raven
SCS 450 controller. The fluid passes through the flow
meter and proceeds to the 5-Way Boom Manifold
valves. If a boom valve is on, the fluid passes to its
respective boom section and is sprayed out the individual
nozzles. See page 83 for a layout of the boom plumbing.
The agitation is set by adjusting the agitation pressure
valve while the pump is at operating speed. Refer to
Application Guide to adjust the agitation.
The optional inductor provides convenient pump-
driven loading of concentrates into the main tank.
There are tank shut off valves ( - ) at each inlet and
outlet. Use these to prevent spills and isolate any leaks.
To operate a correctly connected hydraulic pump, push
the hydraulic lever in the “down” position. When you want
to stop the pump, put the hydraulic lever in the “float”
position.
Do not move the hydraulic lever to the neutral position while
the hydraulic pump is running. To do so may cause damage to
the hydraulic pump.
Pump
Solution Whirlfilter®
Flow Meter
Bypass Control Butterfly Valve
5-Way Boom Manifold Valves
Agitation Gauge
Inductor
Main Inlet Quick Connect
Main Inlet Filter
Flush Tank Inlet Quick Connect
Manual Throttle Valve
Agitator Inlet Shutoff Valves (Normally Open)
Main Inlet Shutoff (Normally Closed)
Flush Tank Inlet Shutoff (Normally Closed)
Main Tank Sump Shutoff (Normally Open)
Whirlfilter Cleanout Shutoff Valve (Normally Closed)
Inductor Outlet/Tank Inlet Shutoff Valve (N.Open)
13
14
15
16
17
18
19
20
21
22
23
30
31
32
33
34
35
10 12
13
14
15
16
16
15 17
1
15
30 35
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Wear Protective Equipment 6
- Handle Chemicals Properly 7
- Confined Space 8
- Use A Safety Chain 8
- Keep Riders Off Machinery 8
- Use Safety Lights and Devices 8
- Check for Overhead Lines 9
- Transport Machinery Safely 9
- Shutdown and Storage 9
- Practice Safe Maintenance 10
- Prepare for Emergencies 10
- Tire Safety 10
- Safety At All Times 11
- Safety Reflectors and Decals 12
- 818-265C 13
- Daytime Reflectors 13
- 818-267C 13
- Amber Reflectors 13
- 500-641M 05/10/2012 14
- 05/10/2012 500-641M 15
- EXCESSIVE SPEED HAZARD 17
- 818-381C 20
- 818-304C 20
- Introduction 21
- Owner Assistance 22
- Preparation and Setup 23
- Hitching with Hydraulic Pump 24
- Axle Spacing 25
- Electrical Connections 26
- Connection Comment 26
- Hydraulic Hookup 27
- Tractor / PTO Shaft Hookup 28
- Leveling Sprayer 29
- Locking System Setup 31
- Hydraulic Pump Setup 31
- Electrical Installation 32
- Raven SCS 450 33
- Hydraulic Valve Control 34
- Foam Marker Control (Option) 34
- Spraying Setup 35
- Manual Throttle Valve 36
- Sprayer Calibration 37
- Operations 40
- Using Hand Wash Tank 41
- Figure 28 44
- Sprayer Tank Plumbing 44
- Operations 41 45
- Figure 29 45
- Boom Plumbing System 45
- Filling Tanks 46
- Filling the Flush Tank 47
- Filling the Main Tank 47
- Adding Chemicals 50
- Inducting Chemicals (Option) 51
- Agitation 52
- Boom Operations 53
- Operating Pump 56
- Unloading Materials 56
- Tank and Boom Flush 57
- Adjustments 61
- Axle Wheel Spacing Adjustment 62
- Break Away Spring 63
- Troubleshooting 64
- Maintenance and Lubrication 66
- Filter Maintenance 67
- Shear Bolt 68
- Pump Maintenance & Repair 69
- Elevator Slide 73
- Quad-Jet Agitators 73
- Tank Entry 74
- Lubrication 75
- Seasonally 77
- Autoboom 78
- Axles and Wheels 78
- Calibration Accessories 79
- Chemical Inductor 79
- High Volume Foam Marker 79
- Gauge Protector 80
- Hitches (Hydraulic Pump Only) 80
- Open Center Hydraulic Kit 80
- Speed Sensors 82
- Appendix 83
- Torque Values 84
- Valve Port Function 85
- 60-Foot Sections 87
- Raven G1 Autoboom Hydraulics 88
- Warranty 89
- Tire Pressure and Torque 92
- Salina, Kansas 67402-5060 USA 96
Related products and manuals for Gardening equipment Great-plains TSF1290 Operator Manual
(5 pages)
(70 pages)© 2020, manymanuals.com. All rights reserved. | 0.141 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals