Great-plains NP4000B Operator Manual User Manual Page 191
- Page / 200
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Great Plains Manufacturing, Inc. Table of Contents Index Appendix C - Accessory Installation 187
2014-05-14 Table of Contents Index 417-199M
Weight Kit Installation
These instructions apply to an installation of an optional
407-740A weight kit.
Tools Required:
• Lift or hoist with a capacity of at least 750 pounds
(340 kg). Two lift lines, each with a capacity of at least
750 pounds (340 kg).
• Tractor for raising and unfolding the applicator.
• Basic hand tools.
1. Raise and unfold the applicator. Leave it hitched or
install parking stands.
Heavy Overhead Object Hazard:
Move only one weight stack at a time. Use an adequate hoist.
Use two or more lines, each rated for the full weight of a single
weight stack. Inspect lines for wear and damage. If the hoist
fails or tips, or a line fails, a weight could fall or swing,
causing serious injury or death.
Refer to Figure 112
2. Locate one:
160-296S NTA WEIGHT BRACKET ASSY
Observe that a weight stack is not symmetrical. The
weight base has a long (outside) notch and a
short (inside) notch .
3. As needed, orient the weight stack prior to line
attachment, so that it is in the correct orientation
when placed on the frame.
4. Connect hoist lines to the weight mounts .
5. With the longer notch toward the wings, and the
shorter notch to machine center, place the weight
in the openings of the rear subframe. Push it fully
forward before releasing the lines.
6. Repeat step 2 through step 5 for all weights.
7. Select four sets:
802-091C HHCS 1/2-13X1 1/2 GR5
803-019C HHCS 5/8-11X2 GR5
and eight:
804-016C WASHER FLAT 1/2 SAE PLT
Place a washer on each bolt . Insert each bolt
between the mounts of adjacent weight stacks.
Secure with second washer and lock nut .
Heavy Overhead Object Hazard:
Do not stand to either side of an elevated weight stack. Keep
body parts away from gaps between the stack and other
machine parts. Remain behind and out from under the elevated
weight stack. Move the stack slowly and carefully. Assume a
line could fail, and that the weights could swing down and to
the side.
Machine Damage Risk:
Do not install a single weight on either side. Do not leave
weight pairs uncoupled on either side. Always install or
remove all four weights. When installed, always use provided
fasteners to couple front and rear weights at their mounts .
Weights are held in place largely by gravity. A single weight,
or uncoupled pair, could tip forward during a sudden stop,
causing machine damage.
Figure 112
Install/Remove Weight Kit
32355
3
U
D
L
R
B
F
13
1
2
3
37
38 40
13
1
2
3
1
2
37
38
40
40 37
3
40
38
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Look for Safety Symbol 6
- Be Aware of Signal Words 6
- Prepare for Emergencies 6
- Use Safety Chains 8
- Avoid High Pressure Fluids 8
- Minimize Radiation Exposure 8
- Keep Riders Off Machinery 8
- Use Safety Lights and Devices 9
- Tires Not a Step 9
- Transport Machinery Safely 10
- Shutdown and Storage 11
- Handle Chemicals Properly 11
- Tire Safety 12
- Practice Safe Maintenance 12
- Safety At All Times 12
- Safety Decals 13
- 818-323C 15
- 818-590C 15
- Danger: Hitch Crush 15
- 848-801C 20
- 848-539C 21
- Introduction 22
- Using This Manual 23
- Owner Assistance 24
- Application Overview 25
- A35 A39 A40 26
- Figure 5 32
- Figure 6 33
- Nutri-Pro 37
- Rear Hitch (Option) 37
- Figure 7 38
- Trailing Nurse Tank Hitch 38
- Preparation and Setup 39
- NP4000A: Get Expert Advice 40
- Pre-Application Setup 40
- 2-Point Hitching 41
- Hydraulic Hose Hookup 45
- Date Code 46
- Motor Model (206N) 46
- Inlet Port 46
- Outlet Port 46
- Leveling Applicator 47
- Wash Water (NP4000A) 51
- Sealer Setup (NP4000A) 51
- Operating Instructions 52
- Fold/Lift Circuit 53
- FOLD / FIELD Switch 53
- Applicator Locks 54
- Raising/Lowering Applicator 55
- Unfolding and Folding 60
- Transport 63
- Final Applicator Setup 64
- Operations 65
- : Pass Planning 70
- Liquid Operations 78
- Liq: Hydraulic Drive Start-Up 81
- Liq: Pauses and Turns 81
- Suspending Application 83
- Liq: Stopping Application 83
- Field Set-Up Checklists 84
- Checklist (Cart Hitched) 85
- Plumbing Checklist Page 85
- Field Operation Checklists 86
- Short-Term Parking 88
- Long-Term Storage 88
- Adjustments 89
- Row Adjustments 90
- Handle Slot Down-Pressure 91
- Tool Bar Height Adjustment 95
- Weight Transfer Adjustment 96
- NUTRI-PRO 97
- Caster Angle Adjustment 98
- Fertilizer Rates 99
- NP4000-1630 Fertilizer Rate 100
- NP4000B-1238 Fertilizer Rate 102
- NP4000B-1240 Fertilizer Rate 103
- Strainer Adjustment 106
- Flow-Based Adjustment 109
- Dead-Head Adjustment 109
- Troubleshooting 110
- FOLD / FIELD Troubleshooting 111
- Maintenance and Lubrication 119
- Avoid Trapped Anhydrous 120
- Avoid Ball Traps 121
- System Discharge 122
- Clearing Plugged Tines 124
- Valve Replacement 127
- Replacement Log 128
- Refrigerant Line 129
- Row Delivery Tubing 130
- Row Vapor Tubing 130
- Metering System Maintenance 131
- Material Clean-Out (Liquid) 132
- Pump Maintenance and Repair 134
- Coulter Disc Replacement 134
- Coulter Spring Setting 135
- Hydraulic Maintenance 136
- Bleeding Fold Hydraulics 137
- Wing Leveling 140
- Rear Eyebolt Adjustment 140
- Caster Brake Adjustment 141
- Chain Maintenance (Option) 142
- Inner Wing Pivots 143
- Outer Wing Pivots 143
- Caster Pivots 143
- Lift- Assist Parallel Arms 144
- Fertilizer Pump Crankshaft 145
- Tire Pressures 145
- As Required 146
- Seasonal 146
- Sub-frame and Tank Selection 148
- Category II Hitch Pin Kit 148
- Rear Hitches 149
- Nurse Tank Light Harness 150
- Row Cleaners 150
- Terra-Tine™ Row Cleaners 150
- Coulters, Blades and Tines 151
- Vantage I Attachment Kits 152
- Coulter Nozzles 152
- Speed Sensor Cable 153
- Speed Sensor 153
- Manifolds and Accessories 154
- Liquid Fertilizer Pumps 155
- Side Dress Extensions 156
- Weight Kit 157
- Specifications and Capacities 158
- Dimensions 161
- Torque Values Chart 163
- Tire Inflation Chart 163
- Plumbing Diagrams 164
- Chain Routing (Option) 172
- Controller System Diagrams 173
- GP: 823-422C 174
- Hydraulic Pump Controller 175
- Hydraulic Diagrams 176
- Pump Hydraulics (Option) 179
- Component Replacement Dates 180
- Post-Delivery Checklist 180
- Lift-Assist Valve Setup 181
- Hydraulic Pump Setup 182
- Console Installation 183
- Side Dress Installation 184
- Refer to Figure 103 186
- 803-027C NUT HEX 3/4-10 PLT 188
- 990-259R EVA TUBING 3/8 ID 189
- Weight Kit Installation 191
- Warranty 192
- Table of Contents Index 199
- Salina, Kansas 67402-5060 USA 200
Related products and manuals for Gardening equipment Great-plains NP4000B Operator Manual
(48 pages)
(50 pages)
(128 pages)© 2020, manymanuals.com. All rights reserved. | 0.161 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals