Great-plains NP4000B Operator Manual User Manual Page 95
- Page / 200
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Great Plains Manufacturing, Inc. Table of Contents Index Adjustments 91
2014-05-14 Table of Contents Index 417-199M
Tool Bar Height Adjustment
Center section tool bar height is set by the tractor hitch.
Lift-assist spacers (page 43) must be selected and in
place to assure front-to-back level.
Wing end tool bar height is set by independent gauge
wheels on each wing end. Wings are maintained at level
in the field with the weight-transfer system (page 92).
1. Move to smooth level ground with soil as similar as
possible to field conditions. Set tractor brakes.
2. Determine the desired coulter depth.
3. Unfold the applicator (page 56).
4. Raise the applicator to bring the wing coulters off the
ground, and the wings slightly above level.
Refer to Figure 63
5. At each gauge wheel, use the crank to remove
tension at the pin . Remove the pin.
6. Use the crank to extend the wheels far enough to
keep the wing coulters off the ground.
7. Unfold the wings until the gauge wheels are on the
ground. Set fold/lift circuit to Float.
8. Use the 2-point hitch to lower the applicator until the
center section coulters are just at ground level.
9. Check frame front-to-back level and adjust spacers
(page 43) as necessary.
10. Adjust the gauge wheel heights to bring the wing
coulters to the same height as the center section
(just above the ground).
11. Measure the length of exposed gauge wheel tube.
12. Crank the wheel up by the desired coulter depth
(exposed tube length becomes length minus the
coulter depth). Capture this setting by re-inserting
and securing the pin .
13. Crank the wheel up until the tube solidly contacts the
pin. This transfers wheel loads to the pin, and not to
the crank.
14. At the center section, measure the tool bar height
above the ground. Operating height is this distance
less the desired coulter depth.
15. Pull forward, lowering the 2-point hitch to operating
height. Set a stop on the 2-point circuit to capture
this height.
16. Adjust weight-transfer (page 92) to hold wings level
at this coulter height for these field conditions.
Equipment Damage Risk:
Use the pin . Crank the tube up against the pin. Wheel loads
transmitted to the crank can damage the crank.
Note: Turn crank clockwise to raise applicator (lower
wheel), and counterclockwise to lower applicator
(raise wheel).
Note: At maximum height, the coulters are off the
ground. This configuration is useful for unfolded
parking, storage and service.
Make a record of the setting needed for coulter
depth prior to setting for maximum.
Figure 63
Gauge Wheel Adjustment
32354
2
3
2
1
1
2
3
3
2
Note: Prior to folding, fold the jack handle down
alongside the jack body. This retains the jack
handle and prevents it from hitting the fertilizer
tanks when folded (if so equipped).
Figure 64
Jack Handle Adjustment
32170
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Look for Safety Symbol 6
- Be Aware of Signal Words 6
- Prepare for Emergencies 6
- Use Safety Chains 8
- Avoid High Pressure Fluids 8
- Minimize Radiation Exposure 8
- Keep Riders Off Machinery 8
- Use Safety Lights and Devices 9
- Tires Not a Step 9
- Transport Machinery Safely 10
- Shutdown and Storage 11
- Handle Chemicals Properly 11
- Tire Safety 12
- Practice Safe Maintenance 12
- Safety At All Times 12
- Safety Decals 13
- 818-323C 15
- 818-590C 15
- Danger: Hitch Crush 15
- 848-801C 20
- 848-539C 21
- Introduction 22
- Using This Manual 23
- Owner Assistance 24
- Application Overview 25
- A35 A39 A40 26
- Figure 5 32
- Figure 6 33
- Nutri-Pro 37
- Rear Hitch (Option) 37
- Figure 7 38
- Trailing Nurse Tank Hitch 38
- Preparation and Setup 39
- NP4000A: Get Expert Advice 40
- Pre-Application Setup 40
- 2-Point Hitching 41
- Hydraulic Hose Hookup 45
- Date Code 46
- Motor Model (206N) 46
- Inlet Port 46
- Outlet Port 46
- Leveling Applicator 47
- Wash Water (NP4000A) 51
- Sealer Setup (NP4000A) 51
- Operating Instructions 52
- Fold/Lift Circuit 53
- FOLD / FIELD Switch 53
- Applicator Locks 54
- Raising/Lowering Applicator 55
- Unfolding and Folding 60
- Transport 63
- Final Applicator Setup 64
- Operations 65
- : Pass Planning 70
- Liquid Operations 78
- Liq: Hydraulic Drive Start-Up 81
- Liq: Pauses and Turns 81
- Suspending Application 83
- Liq: Stopping Application 83
- Field Set-Up Checklists 84
- Checklist (Cart Hitched) 85
- Plumbing Checklist Page 85
- Field Operation Checklists 86
- Short-Term Parking 88
- Long-Term Storage 88
- Adjustments 89
- Row Adjustments 90
- Handle Slot Down-Pressure 91
- Tool Bar Height Adjustment 95
- Weight Transfer Adjustment 96
- NUTRI-PRO 97
- Caster Angle Adjustment 98
- Fertilizer Rates 99
- NP4000-1630 Fertilizer Rate 100
- NP4000B-1238 Fertilizer Rate 102
- NP4000B-1240 Fertilizer Rate 103
- Strainer Adjustment 106
- Flow-Based Adjustment 109
- Dead-Head Adjustment 109
- Troubleshooting 110
- FOLD / FIELD Troubleshooting 111
- Maintenance and Lubrication 119
- Avoid Trapped Anhydrous 120
- Avoid Ball Traps 121
- System Discharge 122
- Clearing Plugged Tines 124
- Valve Replacement 127
- Replacement Log 128
- Refrigerant Line 129
- Row Delivery Tubing 130
- Row Vapor Tubing 130
- Metering System Maintenance 131
- Material Clean-Out (Liquid) 132
- Pump Maintenance and Repair 134
- Coulter Disc Replacement 134
- Coulter Spring Setting 135
- Hydraulic Maintenance 136
- Bleeding Fold Hydraulics 137
- Wing Leveling 140
- Rear Eyebolt Adjustment 140
- Caster Brake Adjustment 141
- Chain Maintenance (Option) 142
- Inner Wing Pivots 143
- Outer Wing Pivots 143
- Caster Pivots 143
- Lift- Assist Parallel Arms 144
- Fertilizer Pump Crankshaft 145
- Tire Pressures 145
- As Required 146
- Seasonal 146
- Sub-frame and Tank Selection 148
- Category II Hitch Pin Kit 148
- Rear Hitches 149
- Nurse Tank Light Harness 150
- Row Cleaners 150
- Terra-Tine™ Row Cleaners 150
- Coulters, Blades and Tines 151
- Vantage I Attachment Kits 152
- Coulter Nozzles 152
- Speed Sensor Cable 153
- Speed Sensor 153
- Manifolds and Accessories 154
- Liquid Fertilizer Pumps 155
- Side Dress Extensions 156
- Weight Kit 157
- Specifications and Capacities 158
- Dimensions 161
- Torque Values Chart 163
- Tire Inflation Chart 163
- Plumbing Diagrams 164
- Chain Routing (Option) 172
- Controller System Diagrams 173
- GP: 823-422C 174
- Hydraulic Pump Controller 175
- Hydraulic Diagrams 176
- Pump Hydraulics (Option) 179
- Component Replacement Dates 180
- Post-Delivery Checklist 180
- Lift-Assist Valve Setup 181
- Hydraulic Pump Setup 182
- Console Installation 183
- Side Dress Installation 184
- Refer to Figure 103 186
- 803-027C NUT HEX 3/4-10 PLT 188
- 990-259R EVA TUBING 3/8 ID 189
- Weight Kit Installation 191
- Warranty 192
- Table of Contents Index 199
- Salina, Kansas 67402-5060 USA 200
Related products and manuals for Gardening equipment Great-plains NP4000B Operator Manual
(48 pages)
(50 pages)
(128 pages)© 2020, manymanuals.com. All rights reserved. | 0.555 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals