Great-plains NP4000B Operator Manual User Manual Page 72
- Page / 200
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
68 2013+ NP4000/A/B Table of Contents Index Great Plains Manufacturing, Inc.
417-199M Table of Contents Index 2014-05-14
20. Open hose inlet end valve ( , if any - tank
depicted in Figure 48 has no hose valves). Check for
leaks and open valves. Expect NO ammonia odor at
this time.
21. Open hose outlet end valve ( , if any - tank
depicted has no hose valves). Check for leaks. In an
all-Great Plains configuration, if there has been no
odor so far, there should be no odor now, as flow is
blocked at the On/Off valve (not visible).
Refer to Figure 49
22. At the meter gauges, pressure gauge should
read within 5 psi
a
of the nurse tank gauge. The flow
divider gauge should be zero. The temperature
gauge is likely to be below ambient.
NH
3
: Starting Application
23. Enter the tractor cab.
24. Check the emergency shut-off rope. Make sure you
know where it is. Make sure the rope cannot slip
away. Leave enough slack in the line for uneven
ground.
Refer to Figure 54
25. At the console, set the POWER switch ON.
26. Set the MASTER switch to ON.
27. Set the BOOMS 1 or BOOMS 1,2 & 3 switches on to
ON.
28. Select the desired RATE preset.
29. Lower applicator to operating depth (if not already
lowered) and begin first pass.
NH
3
: Possible Chemical Hazard:
Anhydrous ammonia is now flowing into the ground. Some
routinely escapes to the atmosphere. Check for leaks. Take
action if strong odor is detected or a leak seen. Turn up wind.
Turn off flow. Check gauges from tractor cab. Engage
emergency shut-off valve if a leak is detected.
Minor odor during application is normal, particularly if the
tractor cab is ever down wind of recent passes.
Strong or irritating odor indicates a problem. Conditions
may not be suitable for application (soil too dry, cloddy
and deeply cracked, for example), or there may be a
system problem.
a. This 5 psi correlation is only true under no-flow conditions. When NH
3
application begins, the pressure reading at the cooler gauge
drops, due to the reduced temperature of the cooled fluid, and pressure losses due to flow in plumbing.
Figure 49
Line-Up Gauge Check
31587
A42
A28
A27
A61a
A61b
A31
A28
A42
A27
Figure 50
Typical Application Screen
31585
- Operator Manual 1
- Table of Contents 3
- Important Safety Information 5
- Look for Safety Symbol 6
- Be Aware of Signal Words 6
- Prepare for Emergencies 6
- Use Safety Chains 8
- Avoid High Pressure Fluids 8
- Minimize Radiation Exposure 8
- Keep Riders Off Machinery 8
- Use Safety Lights and Devices 9
- Tires Not a Step 9
- Transport Machinery Safely 10
- Shutdown and Storage 11
- Handle Chemicals Properly 11
- Tire Safety 12
- Practice Safe Maintenance 12
- Safety At All Times 12
- Safety Decals 13
- 818-323C 15
- 818-590C 15
- Danger: Hitch Crush 15
- 848-801C 20
- 848-539C 21
- Introduction 22
- Using This Manual 23
- Owner Assistance 24
- Application Overview 25
- A35 A39 A40 26
- Figure 5 32
- Figure 6 33
- Nutri-Pro 37
- Rear Hitch (Option) 37
- Figure 7 38
- Trailing Nurse Tank Hitch 38
- Preparation and Setup 39
- NP4000A: Get Expert Advice 40
- Pre-Application Setup 40
- 2-Point Hitching 41
- Hydraulic Hose Hookup 45
- Date Code 46
- Motor Model (206N) 46
- Inlet Port 46
- Outlet Port 46
- Leveling Applicator 47
- Wash Water (NP4000A) 51
- Sealer Setup (NP4000A) 51
- Operating Instructions 52
- Fold/Lift Circuit 53
- FOLD / FIELD Switch 53
- Applicator Locks 54
- Raising/Lowering Applicator 55
- Unfolding and Folding 60
- Transport 63
- Final Applicator Setup 64
- Operations 65
- : Pass Planning 70
- Liquid Operations 78
- Liq: Hydraulic Drive Start-Up 81
- Liq: Pauses and Turns 81
- Suspending Application 83
- Liq: Stopping Application 83
- Field Set-Up Checklists 84
- Checklist (Cart Hitched) 85
- Plumbing Checklist Page 85
- Field Operation Checklists 86
- Short-Term Parking 88
- Long-Term Storage 88
- Adjustments 89
- Row Adjustments 90
- Handle Slot Down-Pressure 91
- Tool Bar Height Adjustment 95
- Weight Transfer Adjustment 96
- NUTRI-PRO 97
- Caster Angle Adjustment 98
- Fertilizer Rates 99
- NP4000-1630 Fertilizer Rate 100
- NP4000B-1238 Fertilizer Rate 102
- NP4000B-1240 Fertilizer Rate 103
- Strainer Adjustment 106
- Flow-Based Adjustment 109
- Dead-Head Adjustment 109
- Troubleshooting 110
- FOLD / FIELD Troubleshooting 111
- Maintenance and Lubrication 119
- Avoid Trapped Anhydrous 120
- Avoid Ball Traps 121
- System Discharge 122
- Clearing Plugged Tines 124
- Valve Replacement 127
- Replacement Log 128
- Refrigerant Line 129
- Row Delivery Tubing 130
- Row Vapor Tubing 130
- Metering System Maintenance 131
- Material Clean-Out (Liquid) 132
- Pump Maintenance and Repair 134
- Coulter Disc Replacement 134
- Coulter Spring Setting 135
- Hydraulic Maintenance 136
- Bleeding Fold Hydraulics 137
- Wing Leveling 140
- Rear Eyebolt Adjustment 140
- Caster Brake Adjustment 141
- Chain Maintenance (Option) 142
- Inner Wing Pivots 143
- Outer Wing Pivots 143
- Caster Pivots 143
- Lift- Assist Parallel Arms 144
- Fertilizer Pump Crankshaft 145
- Tire Pressures 145
- As Required 146
- Seasonal 146
- Sub-frame and Tank Selection 148
- Category II Hitch Pin Kit 148
- Rear Hitches 149
- Nurse Tank Light Harness 150
- Row Cleaners 150
- Terra-Tine™ Row Cleaners 150
- Coulters, Blades and Tines 151
- Vantage I Attachment Kits 152
- Coulter Nozzles 152
- Speed Sensor Cable 153
- Speed Sensor 153
- Manifolds and Accessories 154
- Liquid Fertilizer Pumps 155
- Side Dress Extensions 156
- Weight Kit 157
- Specifications and Capacities 158
- Dimensions 161
- Torque Values Chart 163
- Tire Inflation Chart 163
- Plumbing Diagrams 164
- Chain Routing (Option) 172
- Controller System Diagrams 173
- GP: 823-422C 174
- Hydraulic Pump Controller 175
- Hydraulic Diagrams 176
- Pump Hydraulics (Option) 179
- Component Replacement Dates 180
- Post-Delivery Checklist 180
- Lift-Assist Valve Setup 181
- Hydraulic Pump Setup 182
- Console Installation 183
- Side Dress Installation 184
- Refer to Figure 103 186
- 803-027C NUT HEX 3/4-10 PLT 188
- 990-259R EVA TUBING 3/8 ID 189
- Weight Kit Installation 191
- Warranty 192
- Table of Contents Index 199
- Salina, Kansas 67402-5060 USA 200
Related products and manuals for Gardening equipment Great-plains NP4000B Operator Manual
(48 pages)
(50 pages)
(128 pages)© 2020, manymanuals.com. All rights reserved. | 0.100 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals